If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Wood Drying
Would anyone care to comment on the best way to dry maple without cracking?
I've had mixed success. Thanks, Dan |
#2
|
|||
|
|||
http://www.fpl.fs.fed.us/documnts/fp.../fplgtr113.htm
Chapter three pretty good. Question's too vague to give much more of an answer. "Dan Farrow" wrote in message ... Would anyone care to comment on the best way to dry maple without cracking? I've had mixed success. Thanks, Dan |
#3
|
|||
|
|||
|
#4
|
|||
|
|||
George,
What kind of wood does one use to make a super bowl? How large of a lathe would I need to make one? "George G" wrote in message ... Hi Dan - I save all my old wax left over from Xmas candles. I stand all my Maple logs and branches on end (up to 6 inches) OD. I pour my melted wax on both ends and I have pretty good success with mine. I leave it set in a dry place for over a year. Good Luck---------George -------------------------------------------------------------------------------- |
#5
|
|||
|
|||
|
#6
|
|||
|
|||
An oil based paint works well on basswood, on the ends then stickmit with something heavy and go away for a year
Turt "George G" wrote in message ... Hi Dan - I save all my old wax left over from Xmas candles. I stand all my Maple logs and branches on end (up to 6 inches) OD. I pour my melted wax on both ends and I have pretty good success with mine. I leave it set in a dry place for over a year. Good Luck---------George ---------------------------------------------------------------------------- |
#7
|
|||
|
|||
It depends on how large your piece of wood is. I dryed a piece of maple in the microwave oven in about half an hour. Each time I heated it for one minute the water just ran out the end and a few checks in the wood swelled shut. Depending on the wood type. I understand Oak doesn't have the same capillaries and can explode if heated too hot. I have dryed slabs of walnut by placing them in a plastic bag and sprinkling them with rock salt. Be sure the opening is sloped downward because as the salt draws out the water it will puddle if not drained. Checking was never a problem. On 17 Jan 2005 12:30:05 -0600, "Dan Farrow" wrote: Would anyone care to comment on the best way to dry maple without cracking? I've had mixed success. Thanks, Dan |
#8
|
|||
|
|||
On 17 Jan 2005 12:30:05 -0600, "Dan Farrow"
wrote: Would anyone care to comment on the best way to dry maple without cracking? I've had mixed success. Dan, If you're using the whole log, in the round, it's going to be difficult, because of wood's tendency to shrink in the opposite direction that it grew: ie. contract in a circle. For this reason, you will have much more success if you split the log/limb in half, eliminating the pith, or center portion of the stick. It will dry even more evenly, quickly and with fewer checks if you have a piece large enough to slab it into thick planks or split it into blocks, depending on how you're going to carve it. To facilitate even, slow drying, there are a bunch of things you can do to dry it. #Coat the endgrain with Anchorseal, after spltting it in halves, quarters or slabbing it and put it in a warm (NOT hot), well-ventilated spot, indoors or out, for months...approx. 1year per inch of thickness. Paraffin wax doesn't penetrate far enough, and is too easily peeled off to be effective, and latex paint is "iffy" at best. Dilute white glue has been reported to work fairly well, but whatever you use, don't completely coat the piece, because it's just a waste of material. Wood being made up of a bunch of straws, basically, the vast majority of the moisture escapes through the ends of the wood, rather than the sides. #Cut the wood into the size blocks you're going to carve it into, then weigh them and pack individual blocks into paper bags, surrounded by shavings or sawdust. Take them out and weigh them again, every 4 to 6 weeks, and record the weight on the bag. When they stop losing weight, they are "dry." #Wrap individual blocks in two or more paper bags, again weighing. Every few weeks, take the blocks out, re-weigh, change the inner paper bag, and re-bag. #Cut into individual blocks, dry in the microwave, on 10-20% power or defrost, for a minute to 2 minutes, depending on size, and DON'T LET THE BLOCK GET HOT! That's why they crack. You only want it to be warm to the touch. Let the block cool for __at least__ 45 minutes, longer if it's still warm, and repeat the cycle. You should weigh the block at the beginning and every 3-5 cycles, so you can tell when the piece stops losing weight. #You can make your own kiln, about 1000 different ways, using nothing more complicated than sheets of plastic, a fan and a lightbulb, or more elaborate setups from an old freezer, refrigerator or cooler. There are a lot of sites on the web that have info on this, and I can recommend at least one book that has articles on the topic. Remember, though, if you are using whole logs or limbs to carve, the wood is going to crack, period, and no amount of fancy drying techniques are going to prevent it. Hope this is of some help. -- Chuck *#:^) chaz3913(AT)yahoo(DOT)com Anti-spam sig: please remove "NO SPAM" from e-mail address to reply. September 11, 2001 - Never Forget ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 100,000 Newsgroups ---= East/West-Coast Server Farms - Total Privacy via Encryption =--- |
#9
|
|||
|
|||
Thanks to all for your comments. They were all informative and useful.
Dan "Dan Farrow" wrote in message ... Would anyone care to comment on the best way to dry maple without cracking? I've had mixed success. Thanks, Dan |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
OT - metal vs wood beds... | KDK | Beads | 18 | February 3rd 05 05:23 AM |
Places to buy wood | Bill Tinker | Carving | 2 | January 3rd 04 05:44 PM |
is this all about Wood, or are there Stone carvers here too? | RainLover | Carving | 5 | October 28th 03 08:03 PM |
What wood and what chisels | Princebilly1 | Carving | 10 | September 21st 03 07:54 PM |
3-D Wood Carving Machine | A.T. | Carving | 0 | August 28th 03 05:39 AM |