If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Need help/tips learning Free-Motion Quilting
I am an experienced sewer for 30+ years. I've been quilting for over 20,
machine piecing and usually hand-quilting. Any machine quilting I've done is fairly straight sewing with a walking/even-feed foot. I turn envy-green at the free-motion work, the skill it takes. I have an almost new Brother 8500 machine, and got the special quilting foot, the one with the spring in it. I am using cotton thread, size 80 and 90 needles. I have allowed the machine to auto-set the tension, I've raised it a notch or two, and tried lowering it some. But I continue to break needles. I mean, I'm breaking lots of needles here, just on practice pieces. I rarely get more than 2-3 inches sewn before I can feel the top thread tightening and pulling. The fabric starts to look like it's being "gathered." Bobbin thread is showing on top. (I'm practicing on a "quilt sandwich" - 100% cotton top and bottom, cotton batting in the middle) I've had so many needle breaks that I started to wonder if something was wrong with the machine, although it's less than 3 months old. But it embroiders fine, and I stopped all quilting attempts and pieced a quilt top - it performed flawlessly. With straight seams and the walking foot, it quilted fine. I've done all the straight and nearly straight seams on the quilt, but I soooooo want to learn to stipple!!! I knew this free-motion technique would take lots of practice before I'd do it on a "special piece" and am prepared to put in the necessary time it takes to gain the skill. Figured I would practice on place mats and machine covers/appliance covers when I get some beginner-level skill. But I can't get much practice in when all I'm doing is changing needles (and going to the store for more!) Any of you experienced free-motion quilters out there have any ideas for me? When you stop laughing at my troubles, could you post some hints/tips for me to try? Thanks for all the tips I've already received through this group. Pat S in Delaware |
Ads |
#2
|
|||
|
|||
It just takes a bit of time to get it with free motion quilting. My
guess is you are pulling the fabric rather than guiding. YOu need to turn the balance wheel to get your bobbin thread up in your fabric and then pull that along with the needle thread to the back left a tad. The presser foot needs to be down to engage the tension assembly and the feed dogs need to be down too. Don't pull just let the machine stitch while you guide. Kind of hard to describe but be gentle. I don't explain in writing any better than I do talking but if you google there have been a lot of good threads on the subject. Some of the folks here are real pros and generous with their help. BTW, schmetz are available in 100 packs, atleast 80's that I know of. If all else fails go into the shop you bought the machine and ask for help. Taria Pat S wrote: I am an experienced sewer for 30+ years. I've been quilting for over 20, machine piecing and usually hand-quilting. Any machine quilting I've done is fairly straight sewing with a walking/even-feed foot. I turn envy-green at the free-motion work, the skill it takes. I have an almost new Brother 8500 machine, and got the special quilting foot, the one with the spring in it. I am using cotton thread, size 80 and 90 needles. I have allowed the machine to auto-set the tension, I've raised it a notch or two, and tried lowering it some. But I continue to break needles. I mean, I'm breaking lots of needles here, just on practice pieces. I rarely get more than 2-3 inches sewn before I can feel the top thread tightening and pulling. The fabric starts to look like it's being "gathered." Bobbin thread is showing on top. (I'm practicing on a "quilt sandwich" - 100% cotton top and bottom, cotton batting in the middle) I've had so many needle breaks that I started to wonder if something was wrong with the machine, although it's less than 3 months old. But it embroiders fine, and I stopped all quilting attempts and pieced a quilt top - it performed flawlessly. With straight seams and the walking foot, it quilted fine. I've done all the straight and nearly straight seams on the quilt, but I soooooo want to learn to stipple!!! I knew this free-motion technique would take lots of practice before I'd do it on a "special piece" and am prepared to put in the necessary time it takes to gain the skill. Figured I would practice on place mats and machine covers/appliance covers when I get some beginner-level skill. But I can't get much practice in when all I'm doing is changing needles (and going to the store for more!) Any of you experienced free-motion quilters out there have any ideas for me? When you stop laughing at my troubles, could you post some hints/tips for me to try? Thanks for all the tips I've already received through this group. Pat S in Delaware |
#3
|
|||
|
|||
Pat S wrote:
I have an almost new Brother 8500 machine, and got the special quilting foot, the one with the spring in it. Is that your only option? I'm no expert on machines so check what I'm saying with someone who knows more, but I believe your machine will accomodate a darning foot or free motion foot with a regular needle, not the spring loaded one. The darning foot with the feed dogs down is much easier to use. That springy thingy is for the birds. --Lia |
#4
|
|||
|
|||
This new "springy thingy" just came in the mail today. My machine came with
the embroidery foot, which sort of looks like a darning foot, but won't work for this. Checked the owner's manual (when all else fails, read the book!!) for darning, and it actually tells you to use the buttonhole foot!! Went back and re-read that a few times, figuring the stress of all these needle points ping-ing around had gotten to me. And the "springy thingy" is listed by Brother as a Quilting/Free-motion foot. Here I was, all excited with my package, thinking this would finally be the answer. Whipped dinner onto and then off the table so fast, DH was still chewing and I had the dishes in the dishwasher, just wanted to get back to that sewing machine. Ping, Ping, here I go again. And the feed dogs were down, and I did have the bobbin thread up and both threads held back as I began. Am looking for a dealer that will sell me a dump-truck full of needles Pat in DE "Julia Altshuler" wrote in message news:59ytc.1607$IB.57@attbi_s04... Pat S wrote: I have an almost new Brother 8500 machine, and got the special quilting foot, the one with the spring in it. Is that your only option? I'm no expert on machines so check what I'm saying with someone who knows more, but I believe your machine will accomodate a darning foot or free motion foot with a regular needle, not the spring loaded one. The darning foot with the feed dogs down is much easier to use. That springy thingy is for the birds. --Lia |
#5
|
|||
|
|||
Sorry you are having so much trouble free motioning. I too love to free
motion and have read a lot about it and practice practice and it will come along. Like the other person said...it is very important to get the bobbin thread up...by turning the wheel so the needle goes in...and back up by hand..then grab the bobbin thread and pull and keep to the left. I was told to go about 8 stitches..to secure...then trim those off so they don't get tangled. Plus set your speed of the machine just half power and that way you can put the pedal to the medal all the way and not worry about adjusting the speed then adjust your motion with your hands evenly. I use the emb foot for my free motion...and have a spring foot for my older machine and both work just fine. Good luck.....jj "Julia Altshuler" wrote in message news:59ytc.1607$IB.57@attbi_s04... Pat S wrote: I have an almost new Brother 8500 machine, and got the special quilting foot, the one with the spring in it. Is that your only option? I'm no expert on machines so check what I'm saying with someone who knows more, but I believe your machine will accomodate a darning foot or free motion foot with a regular needle, not the spring loaded one. The darning foot with the feed dogs down is much easier to use. That springy thingy is for the birds. --Lia |
#6
|
|||
|
|||
Pat S wrote:
Am looking for a dealer that will sell me a dump-truck full of needles http://www.kapres.com/needles/needles.htm |
#7
|
|||
|
|||
I wonder if the problem could be your fabric. Recently, I tried to
free-motion a fabric that defied me. Didn't matter which SM, which needle, which foot. It was not that I didn't know how (my stipple-ometer has several million miles on it) or that the SM was out of order (it could do everything else). I had to surrender and give the quilt to the Yorkie. He doesn't like it anymore that the SM did. Is it possible for you to take yourself and the Brother to a dealer to resolve the problem? Maybe, a "Brother" person could tell you a trick specific only to Brother free-motion quilting. GIve them a phone call - the worst that could happen is they will start shouting obscenities at you and you can hang up. We can see that you want to free-motion very badly. It isn't really a tricky thing like making mayonnaise or parallel parking. You can. You will. Polly |
#8
|
|||
|
|||
Pat, where in DE are you? Do you ever get to Philadelphia? I'm due for a
daytrip to Wilmington... --Heidi http://community.webshots.com/user/rabbit2b "Pat S" wrote in message s.com... This new "springy thingy" just came in the mail today. My machine came with the embroidery foot, which sort of looks like a darning foot, but won't work for this. Checked the owner's manual (when all else fails, read the book!!) for darning, and it actually tells you to use the buttonhole foot!! Went back and re-read that a few times, figuring the stress of all these needle points ping-ing around had gotten to me. And the "springy thingy" is listed by Brother as a Quilting/Free-motion foot. Here I was, all excited with my package, thinking this would finally be the answer. Whipped dinner onto and then off the table so fast, DH was still chewing and I had the dishes in the dishwasher, just wanted to get back to that sewing machine. Ping, Ping, here I go again. And the feed dogs were down, and I did have the bobbin thread up and both threads held back as I began. Am looking for a dealer that will sell me a dump-truck full of needles Pat in DE "Julia Altshuler" wrote in message news:59ytc.1607$IB.57@attbi_s04... Pat S wrote: I have an almost new Brother 8500 machine, and got the special quilting foot, the one with the spring in it. Is that your only option? I'm no expert on machines so check what I'm saying with someone who knows more, but I believe your machine will accomodate a darning foot or free motion foot with a regular needle, not the spring loaded one. The darning foot with the feed dogs down is much easier to use. That springy thingy is for the birds. --Lia |
#9
|
|||
|
|||
Thanks, guys, for the chuckles this morning!
--Heidi http://community.webshots.com/user/rabbit2b "Polly Esther" wrote in message link.net... I wonder if the problem could be your fabric. Recently, I tried to free-motion a fabric that defied me. Didn't matter which SM, which needle, which foot. It was not that I didn't know how (my stipple-ometer has several million miles on it) or that the SM was out of order (it could do everything else). I had to surrender and give the quilt to the Yorkie. He doesn't like it anymore that the SM did. Is it possible for you to take yourself and the Brother to a dealer to resolve the problem? Maybe, a "Brother" person could tell you a trick specific only to Brother free-motion quilting. GIve them a phone call - the worst that could happen is they will start shouting obscenities at you and you can hang up. We can see that you want to free-motion very badly. It isn't really a tricky thing like making mayonnaise or parallel parking. You can. You will. Polly |
#10
|
|||
|
|||
Here are some things I do to get my machine to let me fmq:
drop the feed dogs set stitch length to zero lower the presser foot (to engage the tension) take a deep breath before starting Maybe one of these will help? Mary |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Tsunami Relief Drive; Free US Shipping; New Woodrow Studio, Free Spirit, Michael Miller, more at The Virginia Quilter. | The Virginia Quilter | Marketplace | 0 | January 15th 05 03:38 AM |
Free HotMat Mouse Pad - Free International Shipping ! | pg | Marketplace | 0 | December 15th 04 04:27 PM |
Free US Shipping Continues; New Timeless Treasures, Northcott, Michael Miller, more at The Virginia Quilter | The Virginia Quilter | Marketplace | 0 | July 9th 04 04:08 PM |
Free US Shipping Continues; New Fabric from Moda, Woodrow, Avlyn, more at The Virginia Quilter | The Virginia Quilter | Marketplace | 0 | April 23rd 04 07:40 PM |
FREE Stuff That You Can Use | Kim Hang | Beads | 0 | November 25th 03 09:05 PM |