If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
tools for a beginner?
I am going to try my hand at carving and would like some advice on what
tools to begin with. And yes I read the FAQ and searched some through the archives. I also have checked out a few books from the library. But they were not very specific about which tools for which type of carving.... I like this guys work: http://www.donaldpowell.com.au/main.htm Not that I'd expect to ever be that good and certainly not any time soon. But this is the style I would like to strive towards. I believe this is called "in the round" and is probably done with knives as assorted gouges and scorpes. I live near a Woodcraft and have looked on their website but would like some input from some of you here prior to heading down there so that it is not all to over whelming. Thanks in advance for your advice/input. take the un out to respond via e-mail |
Ads |
#2
|
|||
|
|||
A good starter set of Henry Taylor ( Sheffield England ) tools will be a good
investment for hand carving in the round. Plenty of different gouges and chisels and a very good Lignum Vitae mallet is essential Steve |
#3
|
|||
|
|||
Well Lucky1 you have a lot of research ahead of you.(G)
I would suggest you first buy Chris Pye's book(s) Woodcarving, Tools,Material and Equipment. Either the older edition i book (cheaper) or the newer two volume set. You will use his books as a "goto woodcarving bible" for the rest of your carving days.(G) As for the suggestion of Henry Taylor tools, my choice also, but as for the mallet well if you can find a Lignum Vitae mallet nowadays good luck, but again it's my choice.(G) I say look at all the different types of woodcarving before making any choice on tools..and I might also say don't buy a "set" as there will be tools you will almost never use in sets created by manufacturers or sets that such and such carver recommends unless you are actually taking classes from that particular carver. GJP "lucky1" wrote in news:k8KCb.339914$Dw6.1125281@attbi_s02: I am going to try my hand at carving and would like some advice on what tools to begin with. And yes I read the FAQ and searched some through the archives. I also have checked out a few books from the library. But they were not very specific about which tools for which type of carving.... I like this guys work: http://www.donaldpowell.com.au/main.htm Not that I'd expect to ever be that good and certainly not any time soon. But this is the style I would like to strive towards. I believe this is called "in the round" and is probably done with knives as assorted gouges and scorpes. I live near a Woodcraft and have looked on their website but would like some input from some of you here prior to heading down there so that it is not all to over whelming. Thanks in advance for your advice/input. take the un out to respond via e-mail |
#4
|
|||
|
|||
If you're near a Woodcraft, you're probably near some carvers. Ask for some
instruction from them. The guy who taught me owned probably one of every gouge or knife made by any manufacturer, but did most of his work in the round with a Camillus pocketknife. I have never mastered the knife, but find that a dozen tools are sufficient for claw and ball and the odd acanthus carving to embellish my regular woodwork. Fisch is the brand on my set, but the odd pieces are Dastra, Pfeil, and an Ashley Isles. "lucky1" wrote in message news:k8KCb.339914$Dw6.1125281@attbi_s02... I am going to try my hand at carving and would like some advice on what tools to begin with. And yes I read the FAQ and searched some through the archives. I also have checked out a few books from the library. But they were not very specific about which tools for which type of carving.... I like this guys work: http://www.donaldpowell.com.au/main.htm Not that I'd expect to ever be that good and certainly not any time soon. But this is the style I would like to strive towards. I believe this is called "in the round" and is probably done with knives as assorted gouges and scorpes. I live near a Woodcraft and have looked on their website but would like some input from some of you here prior to heading down there so that it is not all to over whelming. |
#5
|
|||
|
|||
On Sat, 13 Dec 2003 19:54:56 GMT, "lucky1"
wrote: I am going to try my hand at carving and would like some advice on what tools to begin with. And yes I read the FAQ and searched some through the archives. I also have checked out a few books from the library. But they were not very specific about which tools for which type of carving.... I like this guys work: http://www.donaldpowell.com.au/main.htm Not that I'd expect to ever be that good and certainly not any time soon. But this is the style I would like to strive towards. I believe this is called "in the round" and is probably done with knives as assorted gouges and scorpes. I live near a Woodcraft and have looked on their website but would like some input from some of you here prior to heading down there so that it is not all to over whelming. Thanks in advance for your advice/input. take the un out to respond via e-mail Hi - I just want to let you know that Woodcraft often has classes, are in touch with local carvers and their clubs. It would be worth a trip in to talk to some of the salesmen there. They are most helpful. You really need to decide on the size and style of carving you wish to do before buying a bunch of tools. This was a good place to start looking for what to do. Ev My woodcarvings are at http://home.earthlink.net/~lvbiggio/ |
#6
|
|||
|
|||
I'd buy either Stubai or Pfeil. Both excellent quality. Either palm tools
or standard size mallet tools.. which ever fits your style of carving. However, my suggestion is to buy the best you can afford.. you will be rewarded. The next suggestion is to buy ONLY what you NEED.. not want. You'll find yourself wanting to fill up a tool box.. but it's easy to buy a bunch of tools you may never use.. wasted money. Wait till you really need something and can't do the process with what you have.. Then pony up the $$... you'll be ahead in the long run. -- Bill Splaine, Healdsburg, CA A Few Woodcarvings: www.picturetrail.com/chips |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
AD ? - Hand Tools | Polly S. | Beads | 37 | July 23rd 12 05:38 AM |
Glass tools and Polyclay? | Stephanie | Beads | 9 | September 28th 04 09:04 PM |
Beginner Lampworking Questions | Maeven | Beads | 11 | September 10th 04 04:55 PM |
wire wrapping tools | Pandi | Beads | 9 | April 26th 04 04:43 PM |
Discount tools and other free stuff. | Ken | Carving | 0 | October 1st 03 08:59 PM |