If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
need help with vacuum casting
"sbright" wrote in message ... Hi folks. I'm having some trouble with my castings lately. They aren't forming completely. [Did these same castings work previously, or are these different?] I'm using a kilnminder to burn out, slow cycle up to 1350 degrees and then back down to 1000. Should I raise the temp? [Not the ultimate temperature, that would be too hot. Investment starts deteriorating above 1350F. But you might pour the flasks hotter, particularly if the castings are very thin, and you're casting gold.] I'm not sure if the wax is completely burned out but after 12 hours I figured it would be. [I'd think so too.] I think my sprues are wide enough. I try to make them at least as wide as the pattern. One last thing is that I'm using filtered water from a water cooler. I had better luck when I was using distilled water but I have a tough time believing that's the problem. [Try it again with distilled water and see if it works any better. I've heard of stranger things. It could be that the minerals in the water are affecting the porosity of your mold. But I'd suspect your metal temperature (too cool) or your vacuuming practice (too late) more than anything to do with the investment.] To many factors to keep experimenting. If anybody has any ideas let me know. Thanks in advance. -Stanley [There are a lot of variables in casting, but short shots point to either not enough heat in the metal, or not enough suction from the vacuum. Changed the oil lately?] Andrew Werby www.unitedartworks.com |
Ads |
#2
|
|||
|
|||
Andrew Werby wrote:
"sbright" wrote in message ... Hi folks. I'm having some trouble with my castings lately. They aren't forming completely. [Did these same castings work previously, or are these different?] I'm using a kilnminder to burn out, slow cycle up to 1350 degrees and then back down to 1000. Should I raise the temp? [Not the ultimate temperature, that would be too hot. Investment starts deteriorating above 1350F. But you might pour the flasks hotter, particularly if the castings are very thin, and you're casting gold.] I'm not sure if the wax is completely burned out but after 12 hours I figured it would be. [I'd think so too.] Wax changes to smut at temperatures over 300 °C and change again to CO2 and H2O at temperatures over 480°C and Oxygen (some fresh air in the kiln). So theoretical every temp beween about 500°C and 780°C (investment start to get destroyed at higher temp) ist working to clean the flask. It is a good idea to look at the main channel. It there is a bright glow, this should be ok. I think my sprues are wide enough. I try to make them at least as wide as the pattern. One last thing is that I'm using filtered water from a water cooler. I had better luck when I was using distilled water but I have a tough time believing that's the problem. [Try it again with distilled water and see if it works any better. I've heard of stranger things. It could be that the minerals in the water are affecting the porosity of your mold. But I'd suspect your metal temperature (too cool) or your vacuuming practice (too late) more than anything to do with the investment.] Sorry, never I could remark that the quality of water could have any influence to this effect. Only if the used water contains solutet gases, it happens, that small gasbubbles are on the surface of wax and so You get small metal shots at the surface. One time heat the water, short before boiling and then cooling down will remove this problem. To many factors to keep True experimenting. If anybody has any ideas let me know. Thanks in advance. -Stanley [There are a lot of variables in casting, but short shots point to either not enough heat in the metal, or not enough suction from the vacuum. Changed the oil lately?] Grommets could be broken. Good luck :-) -- Heinrich Butschal Gutachten, Projektmanagement www.butschal.de |
#3
|
|||
|
|||
Casting update. (Don't laugh)
As I was melting the gold to pour into my 1150 degree flask, I noticed it bubbled. Then I noticed it boiled. Then small pellets started flying out of the crucible. As I took the torch away, it was cherry red, but hardened almost immediately. I know you're not supposed to use old gold, but I wasn't given much choice. I now think that my process is OK, but the gold has a contaminant. I think its lead. Actually, I'm quite sure it's lead. I'll have to refine this batch of gold and try again with new. Thanks for all of your help. -Stanley "Heinrich Butschal" wrote in message ... Andrew Werby wrote: "sbright" wrote in message ... Hi folks. I'm having some trouble with my castings lately. They aren't forming completely. [Did these same castings work previously, or are these different?] I'm using a kilnminder to burn out, slow cycle up to 1350 degrees and then back down to 1000. Should I raise the temp? [Not the ultimate temperature, that would be too hot. Investment starts deteriorating above 1350F. But you might pour the flasks hotter, particularly if the castings are very thin, and you're casting gold.] I'm not sure if the wax is completely burned out but after 12 hours I figured it would be. [I'd think so too.] Wax changes to smut at temperatures over 300 °C and change again to CO2 and H2O at temperatures over 480°C and Oxygen (some fresh air in the kiln). So theoretical every temp beween about 500°C and 780°C (investment start to get destroyed at higher temp) ist working to clean the flask. It is a good idea to look at the main channel. It there is a bright glow, this should be ok. I think my sprues are wide enough. I try to make them at least as wide as the pattern. One last thing is that I'm using filtered water from a water cooler. I had better luck when I was using distilled water but I have a tough time believing that's the problem. [Try it again with distilled water and see if it works any better. I've heard of stranger things. It could be that the minerals in the water are affecting the porosity of your mold. But I'd suspect your metal temperature (too cool) or your vacuuming practice (too late) more than anything to do with the investment.] Sorry, never I could remark that the quality of water could have any influence to this effect. Only if the used water contains solutet gases, it happens, that small gasbubbles are on the surface of wax and so You get small metal shots at the surface. One time heat the water, short before boiling and then cooling down will remove this problem. To many factors to keep True experimenting. If anybody has any ideas let me know. Thanks in advance. -Stanley [There are a lot of variables in casting, but short shots point to either not enough heat in the metal, or not enough suction from the vacuum. Changed the oil lately?] Grommets could be broken. Good luck :-) -- Heinrich Butschal Gutachten, Projektmanagement www.butschal.de |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Problems with a small/medium sized glass casting ... | [email protected] | Glass | 1 | December 6th 04 11:09 PM |
Problems with a small/medium sized glass casting ... | [email protected] | Glass | 0 | December 6th 04 07:14 PM |
slumping casting question | stephen cartwright | Glass | 9 | February 7th 04 07:44 PM |
air pressure for casting | Carl 1 Lucky Texan | Jewelry | 2 | July 27th 03 05:56 PM |
Casting using air pressure | Mike72903 | Jewelry | 6 | July 25th 03 05:41 AM |