A crafts forum. CraftBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » CraftBanter forum » Craft related newsgroups » Pottery
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

FAQ Raku part 2 of 2



 
 
Thread Tools Display Modes
  #1  
Old October 21st 03, 02:13 PM
SBRANFPOTS
external usenet poster
 
Posts: n/a
Default FAQ Raku part 2 of 2

Raku FAQ Part 2 of 2

R.9. All I ever get are bright metallic effects. How do I get more colorful
glaze effects?

This is the exact opposite of the previous question and problem. Brighter
colors need a degree of post firing oxidation in order to develop. There are
several ways to achieve this. When you remove the ware from the kiln, spray the
areas with water where you would like more color to develop before placing the
ware in the reduction container. This will oxidize and cool the glaze. Another
method is to hold the ware in the air for 10 - 30 seconds before reducing the
ware. Allow the combustable material to ignite and cover the container only
after flames have clearly developed. Other potters will uncover the reduction
container after a short time allowing the material to ignite again while
fanning the ware. Using these and other similar techniques you will learn how
to control the amount of metallic and colorful effects on your wares as well as
grey to black unglazed areas.


R.10. Can I preheat my pots in the kiln as it is warming up (starting
w/a cold kiln). I will be using a fiber garbage can kiln with a
lift-off lid, not one where the entire kiln lifts off.I don't
see how my pots will get preheated enough by just setting them on the lid. Do
they get hot enough on a fiber/expanded metal lid?

This question shows a common misunderstanding about the raku process. The only
time you need to be concerned about preheating your ware is when you are doing
multiple firing loads in the same kiln. The first load should always be in a
cold kiln taking the temperature up slowly. Only if you are going to fire
additional loads should you be preheating your pots on or along-side the kiln.
If the lid of the kiln is a wire mesh/fiber lid then you might get enough
radiant heat. Place the pots near the flue opening so they get the heat coming
from the draft. Be careful not to place them too close, too soon, or they may
break. After preheating on top of the kiln you can place the pieces around the
base of the kiln after you remove the fiber chamber, let them heat up there for
a minute or two, then put them on the kiln shelf letting them sit for another
minute, then put the chamber back in place for a minute, then re-light the
burner.


R.11. Must I use a certain type of kiln or can I fire raku in an electric
kiln?

Most any type of kiln can be used for raku as long as it meets certain
requirements of the raku process. It must be located outdoors or in close
proximity to the outdoors. You must be able to easily reach into the kiln to
remove your ware. If you are going to be firing multiple loads the temperature
of the kiln must be easily controlled. An electric kiln is perfectly suitable
for raku although there are some special considerations that require careful
attention. You must remember that you are exposing yourself to live electrical
current when you open an electric kiln so you must protect yourself from any
possible contact with the current. There'll be more on this in a subsequent
revision of this FAQ.


R. 12. When it comes to kilns I’ve heard the terms flue, damper, stack, and
chimney. How do they apply to raku kilns?

All fuel fired kilns need some way for the gases to exit, the air flow to be
controlled, and air to enter the chamber. Conventional kilns have a flue,
damper, and stack (or chimney). The flue is a path in the kiln for the gases to
move through after they have circulated through the kiln on their way to the
stack. The damper is a device, usually a kiln shelf, that slides in and out of
the lower part of the stack in order to control the size of the opening, thus
controlling the exit of the gases and their mixture with air. Raku kilns are
generally small and overpowered. Most have a simple opening in the top of the
chamber covered by a kiln shelf shard. The kiln chamber chamber is essentially
the stack with the opening the flue and the kiln shelf the damper.


R. 13. Why can't I reach temperature no matter how much gas I use?

This is the most common question regarding the raku firing. Successful rise of
temperature in any fuel-fired kiln depends on the correct mixture of air and
fuel. A hotter kiln is not necessarily dependent on more fuel! If there is too
much fuel, the atmosphere will be smoky, full of flames and the temperature
will not rise. Also, if there is too much air, the
temperature will stagnate or fall. Usually, the solution to a situation in
which the kiln doesn't reach temperature is to increase the air in the air/fuel
mixture. In a gas-fired kiln this can be done by increasing the available air
in the burner or around the burner. You can also simply open the flue (the
opening at the top of the kiln). Most potters use a venturi
type burner that has a disk that screws open or closed. Open it for more air.
If you are using a power burner in which a fan is attached, increase the air
flow. Experiment to arrive at the correct mixture but be patient!


R.14. Don't the tongs used to lift the pots leave marks?

Sometimes they do. More often though the glaze is still molten enough that once
the pot is released from the tongs, the marks tend to smooth out. In either
case the tong marks should not be treated as defects but rather as
characteristics of raku.


R.15. I’m confused about the term “reduction.” Can you explain what
this means?

Reduction is a firing term that refers to a lack of oxygen in the combustion
process. This lack of oxygen in the atmosphere causes the fuel to search for
oxygen elsewhere to allow for more complete combustion to take place. This can
take place during a firing as in “reduction stoneware.” In this
conventional situation, the additional oxygen is found chemically bound in the
the clay body and glazes. The result is characteristic reduction effects.
Reduction as it is referred to in raku usually takes place out of the kiln
separate from the actual firing as described earlier. However, just because you
are doing raku doesn’t mean that you can’t experiment with actual reduction
firing in the more conventional sense.

R.16. Must I*remove my ware from the kiln to apply post firing reduction or
can I insert reduction material into the kiln chamber?

As described earlier, post firing reduction is normally done by removing the
ware from the kiln and placing it in a container with your combustable
material. Certain situations may make it difficult to actually remove the wares
from the kiln while they are hot. For instance your piece may be too large or
awkward to handle. In this case you can achieve some post firing success by
shuting off the kiln, adding your reduction material to the chamber, and
closing off all open ports including the flue, peep hole, and burner ports. At
best, the chamber will be only marginally sealed and since effective reduction
depends on on air tight chamber, your reduction will be only partially
successful. If your kiln is a lift off fiber type then you might try removing
it and replacing it with a metal drum or can for the reduction phase.


R.17. Do different types of reduction material give different effects?

The short answer is yes. The long answer is much more complicated! Here is a
medium answer: Your reduction effects are certainly influenced by how much
carbon is in the atmosphere that surrounds your pot. In other words, how much
smoke your pot is quickly subjected to. Some materials have the potential to
release more carbon than others. The condition of your material (wet, damp,
dry) as well as the particle size as in the case of wood materials (sawdust,
shavings, chips) can be important. The type of wood can also affect your
results.


R.18. Must there be clouds of smoke when doing raku?

Raku doesn’t require smoke at all. There are two aspects of the process that
have the potential for creating smoke. If you are using a fuel fired kiln (as
opposed to an electric kiln) then it is likely that there will be at least some
smoke generated during the firing. If you are doing post firing reduction,
there will be smoke created then as well. The amount of smoke is determined by
the efficiency of your reduction technique, the material you are using, and the
amount of material you are using. If you are reducing in a container, the
tighter the lid fits, the less smoke will exit the container. There are other
techniques of reduction that create less smoke than others. Of course if you
are not doing post firing reduction and simply cooling your ware when it comes
from the kiln, then there is no smoke created.


R.19. What is “smokeless raku”?

“Smokeless raku” is not really smokeless at all. The term was coined by
Jerry Caplan who has been developing his techniques for many years. It is a
post firing reduction technique that is designed to produce minimal smoke by
keeping the reduction chamber as air tight as possible. This can be done using
a combination of tight fitting lids with “gaskets” of wet paper or cloth.
The tightest chamber is one made by inverting your container onto a bed of sand
or dirt. Arrange a ring of sand or dirt on the ground for the lid of your
container to fit onto when placed upside down. Place your reduction material
within the ring. Quickly place your ware onto the material and cover it with
the container pushing the rim of the container into the sand. Bury the rim with
additional sand to keep the smoke in.


R.20. What is meant by “naked raku” and “slip resist” in raku?

Naked raku and slip resist refers to a variety of techniques whereby a clay
slip is applied to the surface of the ware. This slip is formulated to peel
away during the firing, and not permanently adhere to the surface. As the slip
peels, shrinks, and separates from the surface it exposes the ware to varying
degrees of post firing reduction. When the piece is cooled, whatever slips
remains on the pot is removed by scraping and cleaning. As a further decorative
process, you can scratch and draw through the slip prior to firing to create
designs.



For a complete handbook covering everything you need to know about the practice
of raku see the book “Raku:*A*Practical Approach, Second Edition” by
Steven Branfman, the author of this FAQ. The book is available at your favorite
book store, pottery supplier, or you can order directly from Steven’s studio,
The Potters Shop. Phone: 781/449



Compiled and first posted June 1996. Revised 9/02. Last posted 10/21/03
copyright Steven Branfman.
Steven Branfman
The Potters Shop
31 Thorpe Rd, Needham MA 02494
phone: 781/449 7687
fax: 781/449 9098
Ads
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
FAQ Raku part 1 of 2 SBRANFPOTS Pottery 0 October 21st 03 02:12 PM
FAQ Raku part 2 of 2 SBRANFPOTS Pottery 0 September 16th 03 11:11 PM
FAQ Raku part 1 of 2 SBRANFPOTS Pottery 0 September 16th 03 11:10 PM
Raku FAQs Tom Buck Pottery 0 July 20th 03 04:49 AM
FAQ:Intro to rec.crafts.pottery Mishy Lowe Pottery 0 July 18th 03 06:05 AM


All times are GMT +1. The time now is 05:10 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2004-2024 CraftBanter.
The comments are property of their posters.