A crafts forum. CraftBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » CraftBanter forum » Craft related newsgroups » Polymer Clay
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Is it "done" or under-done?



 
 
Thread Tools Display Modes
  #1  
Old December 31st 07, 07:47 PM posted to rec.crafts.polymer-clay
bex707
external usenet poster
 
Posts: 1
Default Is it "done" or under-done?

I've been using polymer clay for 12 years, maybe a little more. I
know that recently the makers of FIMO have lowered the recommended
bake temperature. Because I rent, I have always been at the mercy of
whatever oven landlords provided. Because of this, for a long time, I
used a small toaster oven (even though that is not recommended). For
the last couple of years I have been using a larger toaster oven
(outside dimensions 11 in. W by 11 in. deep by 16.5 in. high)
manufactured by GE and sold by Wal-Mart. I have made "creatures" in
the past that were fairly large, but I just winged it and hoped for
the best. I was setting the oven at 265.
..
I'm working on a multi-color heart for an injured veteran of the Iraq
war. I pirated small picture frames from key chains and plan to
suspend them at intervals from the heart so his family can put
favorite photos in them. The heart is open, like an outline; that
"outline" is about an inch wide by half an inch deep. The overall
heart shape is approximately 9 inches at its tallest point by 7 inches
at the widest point.
..
If memory serves I baked this about 40 minutes with the temperature
set at about 250 because an oven thermometer shows that this oven when
set at 250 cycles between about 220 degrees and 260 degrees. I was
inserting wire in holes I poked in the clay before I baked it. The
wire is what the frames will be suspended from. The clay around the
holes crumbled slightly, although I was working it roughly. I am
always hyper-concerned about stuff I make that goes out into the
world...whether it will hold up and is of good quality.
..
Because of this I am wondering if anyone else has input on baking
methods, times, etc. Most of the clay in this heart is FIMO, but
there is PRIMO in it, too. I'm concerned because the idea of the
heart is for it to hang...like on an I.V. pole. I've made hearts
before that have dangled from I.V. poles, swinging and bumping, and
there hasn't been a problem. However, those were perhaps 3 in. wide
by 4.5 in. tall and 1/4 to 1/2 in. thick.
..
I'm sorry this post is so long, especially for a first-time poster. I
became aware of this group when I read stuff on the web about the new
FIMO baking temperature.
Thanks!
Ads
  #2  
Old January 1st 08, 02:55 AM posted to rec.crafts.polymer-clay
Barbara Forbes-Lyons
external usenet poster
 
Posts: 408
Default Is it "done" or under-done?

The best thing is to get an oven thermometer, really two, and place one
near the front of the oven, and another near the back. Let the oven warm
up for a while and check the temperature. I find that placing a small
ceramic tile on the grid helps to regulate temperature better in small
ovens.

If you are mixing older Fimo with Premo you can bake safely at 275. New
Fimo cannot be mixed with anything except new Fimo. The baking temp is
significantly lower than any other clay to insure that a higher temp
clay will not properly cure.

That said, your crumbling issue could be because the clay was either
under down or over done.

Barbara

Bead & Polymer Clay Habitué

There is a very fine line between a hobby and mental illness. (Dave Barry)

http://www.penguintrax.com
http://www.backseatgrammarian.com
http://www.polymerclayworkshops.com



bex707 wrote:
I've been using polymer clay for 12 years, maybe a little more. I
know that recently the makers of FIMO have lowered the recommended
bake temperature. Because I rent, I have always been at the mercy of
whatever oven landlords provided. Because of this, for a long time, I
used a small toaster oven (even though that is not recommended). For
the last couple of years I have been using a larger toaster oven
(outside dimensions 11 in. W by 11 in. deep by 16.5 in. high)
manufactured by GE and sold by Wal-Mart. I have made "creatures" in
the past that were fairly large, but I just winged it and hoped for
the best. I was setting the oven at 265.
.
I'm working on a multi-color heart for an injured veteran of the Iraq
war. I pirated small picture frames from key chains and plan to
suspend them at intervals from the heart so his family can put
favorite photos in them. The heart is open, like an outline; that
"outline" is about an inch wide by half an inch deep. The overall
heart shape is approximately 9 inches at its tallest point by 7 inches
at the widest point.
.
If memory serves I baked this about 40 minutes with the temperature
set at about 250 because an oven thermometer shows that this oven when
set at 250 cycles between about 220 degrees and 260 degrees. I was
inserting wire in holes I poked in the clay before I baked it. The
wire is what the frames will be suspended from. The clay around the
holes crumbled slightly, although I was working it roughly. I am
always hyper-concerned about stuff I make that goes out into the
world...whether it will hold up and is of good quality.
.
Because of this I am wondering if anyone else has input on baking
methods, times, etc. Most of the clay in this heart is FIMO, but
there is PRIMO in it, too. I'm concerned because the idea of the
heart is for it to hang...like on an I.V. pole. I've made hearts
before that have dangled from I.V. poles, swinging and bumping, and
there hasn't been a problem. However, those were perhaps 3 in. wide
by 4.5 in. tall and 1/4 to 1/2 in. thick.
.
I'm sorry this post is so long, especially for a first-time poster. I
became aware of this group when I read stuff on the web about the new
FIMO baking temperature.
Thanks!

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
"Butterfly Dress" in "Beads Buttons and Lace/Romantic Style" both by Jennie Atkinson Roseagh Yarn 4 July 31st 07 10:00 AM
AD - "Adornare" and "Nightsky" Dawn >^..^ Beads 10 December 6th 06 04:19 PM
OT proposed discussion: How did you learn to be a "woman" rather than a "girl"? Tricia Quilting 104 September 1st 06 10:28 PM
OT proposed discussion: How did you learn to be a "woman" ratherthan a "girl"? off kilter quilter Quilting 0 August 30th 06 02:33 AM


All times are GMT +1. The time now is 10:18 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 CraftBanter.
The comments are property of their posters.