If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
help me please
Hi all,
new to rubber stamping and have been trying a few things out over the last few days but need some help on embossing i stamp ok with clear ink then sprinkle powder on but when i come to take the powder off to heat up, it seems to have speks of the stuff all over the place, any tips before i go back to model making lol cheers and all the best stuart |
Ads |
#2
|
|||
|
|||
help me please
There are little bags that contain something (I think maybe talc?) that you
can purchase very inexpensively. You wipe it across the card BEFORE stamping. When you pour off your excess powder it won't stick to the card. I think mine cost about $3-$4US. Mine is called an Embossing Buddy, but I think that might be a brand name. You should be able to find something at a local craft store if you tell them what problem you are having. Good Luck! Cecelia |
#3
|
|||
|
|||
help me please
DarkVisor wrote:
snip i stamp ok with clear ink then sprinkle powder on but when i come to take the powder off to heat up, it seems to have speks of the stuff all over the place, any tips before i go back to model making lol Stuart, Two suggestions: 1) Use a fine paintbrush to carefully brush off excess powder. 2) Turn your card (or whatever) upside down and tap fairly hard on the card with your finger to release the excess. If you did a good job of applying the ink, the powder you *do* want should stay stuck OK when you do this. Excess powder sticking is usually more of a static electricity issue. Anything you can do to reduce the static electricity in the environment will help, such as running a humidifier in the room in winter, especially if you have central air. Good luck! Barbara |
#4
|
|||
|
|||
help me please
Cecelia wrote:
There are little bags that contain something (I think maybe talc?) that you can purchase very inexpensively. You wipe it across the card BEFORE stamping. When you pour off your excess powder it won't stick to the card. I think mine cost about $3-$4US. Mine is called an Embossing Buddy, but I think that might be a brand name. You should be able to find something at a local craft store if you tell them what problem you are having. Good Luck! Cecelia Hmmmm....I wonder if rubbing a fabric softener sheet across the card would do the same thing? Something I might experiment with.... Barbara |
#5
|
|||
|
|||
help me please
I have successfully used the embossing buddy that Cecelia mentioned, as well
as the fabric softener sheet. Both work well, I have also used a makeup brush to dust corn starch over the paper before I stamp my embossing ink. It worked well too. Also as Barbara said, give it a GOOD tap before you heat. If you use one of the preceding ideas and tap well you should have much better results. Good luck! Arleen "DarkVisor" wrote in message ... Hi all, new to rubber stamping and have been trying a few things out over the last few days but need some help on embossing i stamp ok with clear ink then sprinkle powder on but when i come to take the powder off to heat up, it seems to have speks of the stuff all over the place, any tips before i go back to model making lol cheers and all the best stuart |
#6
|
|||
|
|||
help me please
Stuart,
Another good suggestion is to try not to handle your cardstock too much before stamping on it - hold it by the edges rather than sticking finger and thumb firmly in the middle (which was what I used to do...!) The grease on your fingers will stick onto the card and attract embossing powder like anything, so the less fingerprints on the card, the less stray powder particles. Hope this helps, Suzie B -- "From the internet connection under the (undamaged end of the) pier!" Southend, UK -- Please remove NOSPAM when emailing me! http://community.webshots.com/user/suziekga |
#7
|
|||
|
|||
help me please
Hey i like these ideas too cause im new to embossing and i was having
the same trouble..i will try the fabric sheet first and see if this is a goody..thanks all.. |
#8
|
|||
|
|||
help me please
Hi,
what works for me is using a small paint brush to clean it up a bit or using the Stampin'UP embossing buddy it's to be rubbed on the cardstock before you stamp and emboss it's price runs $4.50 eacg...........hope this helps you! Shell Stampin'Up Demonstrator in Alaska DarkVisor wrote: Hi all, new to rubber stamping and have been trying a few things out over the last few days but need some help on embossing i stamp ok with clear ink then sprinkle powder on but when i come to take the powder off to heat up, it seems to have speks of the stuff all over the place, any tips before i go back to model making lol cheers and all the best stuart |
#9
|
|||
|
|||
help me please
Barbara Hass wrote: Hmmmm....I wonder if rubbing a fabric softener sheet across the card would do the same thing? Something I might experiment with.... Barbara Fabric softener sheets work very well for reducing stray embossing powder, but you should use a *used* sheet. Otherwise, it may leave a residue on your paper. Do your laundry first, then you can emboss. :-) Sincerely, Risible |
#10
|
|||
|
|||
help me please
Yes be sure to use a 'used' dryer sheet -- or you will have more of a mess
than you ever planned for. Don't ask me how I know. lol Mary Ann "Risible" wrote in message oups.com... Barbara Hass wrote: Hmmmm....I wonder if rubbing a fabric softener sheet across the card would do the same thing? Something I might experiment with.... Barbara Fabric softener sheets work very well for reducing stray embossing powder, but you should use a *used* sheet. Otherwise, it may leave a residue on your paper. Do your laundry first, then you can emboss. :-) Sincerely, Risible |
Thread Tools | |
Display Modes | |
|
|