If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Witness cones
Hello Everyone,
Does anyone know of any possible reason I should not throw my used witness cones away? Thanks, Sandi |
Ads |
#2
|
|||
|
|||
1. because they look cool scattered all around your kiln! (along with kiln
dragons) 2. kids like them 3. they are a handy way to explain to visiters how the kiln works. steve Subject: Witness cones From: (sandi) Date: 8/27/2004 6:07 PM Pacific Daylight Time Message-id: Hello Everyone, Does anyone know of any possible reason I should not throw my used witness cones away? Thanks, Sandi steve graber |
#3
|
|||
|
|||
"Slgraber" wrote in message ... 1. because they look cool scattered all around your kiln! (along with kiln dragons) 2. kids like them 3. they are a handy way to explain to visiters how the kiln works. steve Someone I know even used them in a work. She takes old printer frames, you know little shelves and fills them with lovely porcelain fish - usually. On though had the usual porcelain fish and the witness cones in one of the little shelves. ) Not quite my thing, but it did look cool |
#4
|
|||
|
|||
On Mon, 30 Aug 2004 12:18:55 +1200, "annemarie"
wrote: "Slgraber" wrote in message ... 1. because they look cool scattered all around your kiln! (along with kiln dragons) 2. kids like them 3. they are a handy way to explain to visiters how the kiln works. steve Someone I know even used them in a work. She takes old printer frames, you know little shelves and fills them with lovely porcelain fish - usually. On though had the usual porcelain fish and the witness cones in one of the little shelves. ) Not quite my thing, but it did look cool The bent cones strike me as perfect for a "bear claw" necklace. The catch is getting holes in them for stringing. Once they're fired they are hard to drill... maybe a diamond burr? I have tried drilling before firing, but not only are they pretty fragile, but also you don't want to drill too high up on the cone or you will change the bending behavior. I put this project on a back burner awaiting future inspiration... g Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com |
#5
|
|||
|
|||
"Bob Masta" wrote in message ... On Mon, 30 Aug 2004 12:18:55 +1200, "annemarie" wrote: "Slgraber" wrote in message ... 1. because they look cool scattered all around your kiln! (along with kiln dragons) 2. kids like them 3. they are a handy way to explain to visiters how the kiln works. steve Someone I know even used them in a work. She takes old printer frames, you know little shelves and fills them with lovely porcelain fish - usually. On though had the usual porcelain fish and the witness cones in one of the little shelves. ) Not quite my thing, but it did look cool The bent cones strike me as perfect for a "bear claw" necklace. The catch is getting holes in them for stringing. Once they're fired they are hard to drill... maybe a diamond burr? I have tried drilling before firing, but not only are they pretty fragile, but also you don't want to drill too high up on the cone or you will change the bending behavior. I put this project on a back burner awaiting future inspiration... g perhaps you would have to set them in silver or gold to hold them in place |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Heat Work Problem | pete | Pottery | 10 | October 30th 03 07:53 AM |
LONG post on results of "Glazus Interuptus" | GaSeku | Pottery | 13 | September 21st 03 12:37 PM |
kilns and cones | David Coggins | Pottery | 4 | August 2nd 03 04:46 PM |
Cone question | L.Mac | Pottery | 8 | July 30th 03 01:48 PM |
FAQ:Intro to rec.crafts.pottery | Mishy Lowe | Pottery | 0 | July 18th 03 06:05 AM |