If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
SK840 Jams with Ribber
Hi all, I'm at my wits end. I have an sk840 and I want to do a double faced jacquard. So I bought a srp60n ribber to do the backface. Whenever both the main carriage and the ribber carriage knit at the same time the carriage gets almost impossible to move across.
I have to admit that I am incredibly new to knitting. Does anyone have any ideas why this may happen? I have all the settings like the manual but feel maybe I am setting up something wrong. Or if you could point me in the direction of a tutorial that would be great? FYI If I set up the carriages so only the main carriage or only the ribber needles knit then its fine, its only when they knit at the same time. Thanks, Dan |
Ads |
#2
|
|||
|
|||
SK840 Jams with Ribber
Probably the sponge bar in the main bed.
-- Regards, David Toft "Dan" wrote in message ... Hi all, I'm at my wits end. I have an sk840 and I want to do a double faced jacquard. So I bought a srp60n ribber to do the backface. Whenever both the main carriage and the ribber carriage knit at the same time the carriage gets almost impossible to move across. I have to admit that I am incredibly new to knitting. Does anyone have any ideas why this may happen? I have all the settings like the manual but feel maybe I am setting up something wrong. Or if you could point me in the direction of a tutorial that would be great? FYI If I set up the carriages so only the main carriage or only the ribber needles knit then its fine, its only when they knit at the same time. Thanks, Dan |
#3
|
|||
|
|||
SK840 Jams with Ribber
I have found a lot of those answers on you tube.
Ggive it a try.. good luck |
#4
|
|||
|
|||
SK840 Jams with Ribber
On Wednesday, April 17, 2013 9:51:38 PM UTC+1, Dan wrote:
I have to admit that I am incredibly new to knitting. Does anyone have any ideas why this may happen? I have all the settings like the manual but feel maybe I am setting up something wrong. Or if you could point me in the direction of a tutorial that would be great? Sounds like your ribber is too high. Have a look on www.needlesofsteel.org.uk under downloads, there's a pdf there on how to lower the ribber. It's a one time only adjustment. Regards, Jane |
#5
|
|||
|
|||
SK840 Jams with Ribber
El dimecres 17 d'abril de 2013 22:51:38 UTC+2, Dan va escriu
Hi all, I'm at my wits end. I have an sk840 and I want to do a double faced jacquard. So I bought a srp60n ribber to do the backface. Whenever both the main carriage and the ribber carriage knit at the same time the carriage gets almost impossible to move across. I have to admit that I am incredibly new to knitting. Does anyone have any ideas why this may happen? I have all the settings like the manual but feel maybe I am setting up something wrong. Or if you could point me in the direction of a tutorial that would be great? FYI If I set up the carriages so only the main carriage or only the ribber needles knit then its fine, its only when they knit at the same time. Thanks, Dan Hi Dan, Could you fix it ?? I have the same knitting machine and the ribber bed too since few months ago and I have the same feeling. Thanks, Miquel |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ribber | [email protected] | Machine Knit | 1 | July 15th 06 10:44 AM |
Ribber Problems | Davidhab | Machine Knit | 2 | October 9th 05 12:39 PM |
Help with brother ribber, please | [email protected] | Machine Knit | 5 | May 25th 05 01:56 AM |
Singer LK100 carriage jams | LL Phillips | Machine Knit | 2 | September 29th 04 11:31 AM |
ribber combs | reltuc | Machine Knit | 0 | September 25th 03 02:38 PM |