If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
DIAMOND CORE BITS
Hi,
a while ago a guy was posting to this group advertising sets of diamond core bits. 4 sizes thru 1/2" anyone have his address. I am in need of 1/2 OD bits. any advise on good bits thks bg -- "Poor people have access to the courts in the same sense that Christians had access to the lions." - Judge Earl Johnson Jr. |
Ads |
#2
|
|||
|
|||
www.harborfreight.com may have what you are looking for
"Boner the Cat" wrote in message . com... Hi, a while ago a guy was posting to this group advertising sets of diamond core bits. 4 sizes thru 1/2" anyone have his address. I am in need of 1/2 OD bits. any advise on good bits thks bg -- "Poor people have access to the courts in the same sense that Christians had access to the lions." - Judge Earl Johnson Jr. |
#3
|
|||
|
|||
Boner the Cat wrote:
Hi, a while ago a guy was posting to this group advertising sets of diamond core bits. 4 sizes thru 1/2" anyone have his address. I am in need of 1/2 OD bits. any advise on good bits thks bg -- "Poor people have access to the courts in the same sense that Christians had access to the lions." - Judge Earl Johnson Jr. http://www.waleapparatus.com/search_...N=&PRODUCT_ID= -- Jack http://photos.yahoo.com/bc/xmissionbobo/ |
#4
|
|||
|
|||
this guys prices are just so over the top that it is a wonder he sells
anything. the Chinese guy was selling 4 bits for 12.95 and they are good bits. "nJb" wrote in message ... Boner the Cat wrote: Hi, a while ago a guy was posting to this group advertising sets of diamond core bits. 4 sizes thru 1/2" anyone have his address. I am in need of 1/2 OD bits. any advise on good bits thks bg -- "Poor people have access to the courts in the same sense that Christians had access to the lions." - Judge Earl Johnson Jr. http://www.waleapparatus.com/search_...N=&PRODUCT_ID= -- Jack http://photos.yahoo.com/bc/xmissionbobo/ |
#5
|
|||
|
|||
hey they have the 1/2 " I require..many thks
bg "Moonraker" wrote in message news www.harborfreight.com may have what you are looking for "Boner the Cat" wrote in message . com... Hi, a while ago a guy was posting to this group advertising sets of diamond core bits. 4 sizes thru 1/2" anyone have his address. I am in need of 1/2 OD bits. any advise on good bits thks bg -- "Poor people have access to the courts in the same sense that Christians had access to the lions." - Judge Earl Johnson Jr. |
#6
|
|||
|
|||
They also have some small, thin diamond cut-off wheels that I use for
cutting brass and zinc. There are 5 of them and an arbor for your Dremel on a blister pack. Reg price is $10., on sale this next week or so for $2.95. I'm stocking up!!! "Boner the Cat" wrote in message om... hey they have the 1/2 " I require..many thks bg "Moonraker" wrote in message news www.harborfreight.com may have what you are looking for |
#7
|
|||
|
|||
Boner the Cat wrote:
this guys prices are just so over the top that it is a wonder he sells anything. the Chinese guy was selling 4 bits for 12.95 and they are good bits. I buy a lot of things from the Chinese guy and most of it is fine. Some if it is junk. For example, a heavy duty wire wheel for my angle grinder. The price is great at $4.99. But it is so out of balance that you can't use it for very long without destroying your hands. I offered you an alternative source from a quality company. If the Chinese core drills do the job, by all means buy them. Report back with your results. -- Jack http://photos.yahoo.com/bc/xmissionbobo/ |
#8
|
|||
|
|||
I use those thin cut-off wheels for zinc and brass
They work great! But when it comes to lead---- I'm still deforming the lead no matter what I use, including the lead knife. Especially when cutting an angle greater than 45 degrees. Suggestions? Hal "Moonraker" wrote in message ... They also have some small, thin diamond cut-off wheels that I use for cutting brass and zinc. There are 5 of them and an arbor for your Dremel on a blister pack. Reg price is $10., on sale this next week or so for $2.95. I'm stocking up!!! "Boner the Cat" wrote in message om... hey they have the 1/2 " I require..many thks bg "Moonraker" wrote in message news www.harborfreight.com may have what you are looking for |
#9
|
|||
|
|||
http://cgi.ebay.com/ws/eBayISAPI.dll...tem=3714282152
I'll let you know how it works as soon as it gets here. It uses a single edge razorblade in a guillotine fashion. "Harold E. Keeney (Hal)" wrote in message ... I use those thin cut-off wheels for zinc and brass They work great! But when it comes to lead---- I'm still deforming the lead no matter what I use, including the lead knife. Especially when cutting an angle greater than 45 degrees. Suggestions? Hal "Moonraker" wrote in message ... They also have some small, thin diamond cut-off wheels that I use for cutting brass and zinc. There are 5 of them and an arbor for your Dremel on a blister pack. Reg price is $10., on sale this next week or so for $2.95. I'm stocking up!!! "Boner the Cat" wrote in message om... hey they have the 1/2 " I require..many thks bg "Moonraker" wrote in message news www.harborfreight.com may have what you are looking for |
#10
|
|||
|
|||
At least for larger cuts, I use an ordinary bandsaw for cutting lead and
aluminum.... But then, they aren't exactly precision cuts! :-) --Rick "Harold E. Keeney (Hal)" wrote: I use those thin cut-off wheels for zinc and brass They work great! But when it comes to lead---- I'm still deforming the lead no matter what I use, including the lead knife. Especially when cutting an angle greater than 45 degrees. Suggestions? Hal "Moonraker" wrote in message ... They also have some small, thin diamond cut-off wheels that I use for cutting brass and zinc. There are 5 of them and an arbor for your Dremel on a blister pack. Reg price is $10., on sale this next week or so for $2.95. I'm stocking up!!! "Boner the Cat" wrote in message om... hey they have the 1/2 " I require..many thks bg "Moonraker" wrote in message news www.harborfreight.com may have what you are looking for |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
diamond beads | Kevin | Beads | 2 | June 12th 13 06:05 PM |
Home diamond identification? | ~Candace~ | Beads | 12 | August 14th 04 07:07 PM |
Hickory Door Makers Bits | Ronald Murray | Carving | 0 | February 26th 04 03:55 AM |
diamond bits..who is giving great deals on the small bits | Boner the Cat | Glass | 4 | January 15th 04 08:15 PM |
Core drills - source wanted | derek | Glass | 3 | November 25th 03 01:48 PM |