If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Pictures Posted
If anyone is interested, I just posted a few of my miniature turnings
on alt.binaries.crafts.pictures and alt.binaries.pictures.crafts. -- Chuck *#:^) chaz3913(AT)yahoo(DOT)com Anti-spam sig: please remove "NO SPAM" from e-mail address to reply. September 11, 2001 - Never Forget -----= Posted via Newsfeeds.Com, Uncensored Usenet News =----- http://www.newsfeeds.com - The #1 Newsgroup Service in the World! -----== Over 100,000 Newsgroups - 19 Different Servers! =----- |
Ads |
#2
|
|||
|
|||
Ooo, They're beautiful! That's something I'd like to learn to do some day.
"Chuck" wrote in message ... If anyone is interested, I just posted a few of my miniature turnings on alt.binaries.crafts.pictures and alt.binaries.pictures.crafts. -- Chuck *#:^) chaz3913(AT)yahoo(DOT)com Anti-spam sig: please remove "NO SPAM" from e-mail address to reply. September 11, 2001 - Never Forget -----= Posted via Newsfeeds.Com, Uncensored Usenet News =----- http://www.newsfeeds.com - The #1 Newsgroup Service in the World! -----== Over 100,000 Newsgroups - 19 Different Servers! =----- |
#3
|
|||
|
|||
"Chuck" wrote in message ... If anyone is interested, I just posted a few of my miniature turnings on alt.binaries.crafts.pictures and alt.binaries.pictures.crafts. Beautiful!! |
#4
|
|||
|
|||
Chuck wrote:
If anyone is interested, I just posted a few of my miniature turnings on alt.binaries.crafts.pictures and alt.binaries.pictures.crafts. they're great, i envy you.... -- vixx' |
#5
|
|||
|
|||
On Sat, 6 Mar 2004 05:57:51 -0500, "havana bill & holly"
wrote: Ooo, They're beautiful! That's something I'd like to learn to do some day. Thank you. And it's really a lot easier than you might think. Actually, you don't even need a lathe for some projects. My first turned piece was a perfect little brass candlestick that I turned on a drill press, with files and sandpaper. There's an article I wrote on the rcd website that talks about turning without a lathe. Take a gander at it if you get time. And thanks to the rest for your kind comments. -- Chuck *#:^) chaz3913(AT)yahoo(DOT)com Anti-spam sig: please remove "NO SPAM" from e-mail address to reply. September 11, 2001 - Never Forget -----= Posted via Newsfeeds.Com, Uncensored Usenet News =----- http://www.newsfeeds.com - The #1 Newsgroup Service in the World! -----== Over 100,000 Newsgroups - 19 Different Servers! =----- |
#6
|
|||
|
|||
Sweet ! Very nice Chuck. Clean with good form.
Thanks for sharing, Patrick Chuck wrote in message ... If anyone is interested, I just posted a few of my miniature turnings on alt.binaries.crafts.pictures and alt.binaries.pictures.crafts. September 11, 2001 - Never Forget == Over 100,000 Newsgroups - 19 Different Servers! =----- |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
New pictures of my work | roxan | Beads | 6 | February 22nd 04 12:05 PM |
new pictures (opinions wanted) | Beadbimbo | Beads | 41 | February 10th 04 12:39 PM |
Pictures of new work and my webpage | Marisa Cappetta | Beads | 12 | September 21st 03 03:37 AM |
Tall Ships and Zoo Pictures: OT | Tink | Beads | 3 | July 17th 03 03:08 PM |