A crafts forum. CraftBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » CraftBanter forum » Textiles newsgroups » Sewing
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Problems with a steam iron



 
 
Thread Tools Display Modes
  #1  
Old April 2nd 08, 07:33 AM posted to rec.crafts.textiles.sewing
Just Askin
external usenet poster
 
Posts: 2
Default Problems with a steam iron

I recently bought a brand new Black & Decker Steam Advantage iron (model
F2200). This is one with a "Ceramic Glide" soleplate. I've owned it less
than a week and I am already having problems with it. The specific problem
I am having is that on occasion it is staining my clothes. This happens
when I am ironing over a thick seam, say, the outside corner of the pocket
on the front of a shirt. The iron is leaving a thin, brown stain there.
Sometimes I can brush off what seems to be some residue there, but sometimes
not.

When I examine the soleplate I see some brown stains immediately below the
"top" steam vent, extending in a V-shape in each direction. This stained
area feels slightly rough, as though there is residue there.

Compared with my old iron, which had a non-stick (Teflon?) soleplate, I've
noticed that the ceramic soleplate of this new iron is more "sticky," and I
have to let the steam flow really build up before I can move the iron back
and forth easily. This soleplate also seems to get hotter at a given fabric
heat/steam setting.

I have ironed almost exclusively dress shirts, both 100% cotton and
poly/cotten shirts, with this iron. I am using the recommended heat/steam
setting for the fabric. I have been filling the iron with store-bought,
distilled water.

I have two questions:

(1) What is causing this problem? Is the recommended setting too hot? Is
this residue microscopic, burned, fabric particles?

(2) How can I clean this material off the soleplate?

Thanks in advance. I saw from searching Google that problems with steam
irons have been discussed in this group in the past.


Ads
  #2  
Old April 2nd 08, 08:24 AM posted to rec.crafts.textiles.sewing
claireowen
external usenet poster
 
Posts: 2
Default Problems with a steam iron

Just Askin a écrit :
I recently bought a brand new Black & Decker Steam Advantage iron (model
F2200). This is one with a "Ceramic Glide" soleplate. I've owned it less
than a week and I am already having problems with it. The specific problem
I am having is that on occasion it is staining my clothes. This happens
when I am ironing over a thick seam, say, the outside corner of the pocket
on the front of a shirt. The iron is leaving a thin, brown stain there.
Sometimes I can brush off what seems to be some residue there, but sometimes
not.

When I examine the soleplate I see some brown stains immediately below the
"top" steam vent, extending in a V-shape in each direction. This stained
area feels slightly rough, as though there is residue there.

Compared with my old iron, which had a non-stick (Teflon?) soleplate, I've
noticed that the ceramic soleplate of this new iron is more "sticky," and I
have to let the steam flow really build up before I can move the iron back
and forth easily. This soleplate also seems to get hotter at a given fabric
heat/steam setting.

I have ironed almost exclusively dress shirts, both 100% cotton and
poly/cotten shirts, with this iron. I am using the recommended heat/steam
setting for the fabric. I have been filling the iron with store-bought,
distilled water.

I have two questions:

(1) What is causing this problem? Is the recommended setting too hot? Is
this residue microscopic, burned, fabric particles?

(2) How can I clean this material off the soleplate?

Thanks in advance. I saw from searching Google that problems with steam
irons have been discussed in this group in the past.



I had similar problems to yours with my steam generator iron after I ran
a descaler through it!! mine is supposed to be run on boiled water not
distilled or straight tap water according to the manufacturers
instructions. However I descaled it as we live in a hard water area, and
it was showing signs of scale.

I solved it by literally picking the whole unit up, after unplugging it
and taking it to the sink filling it with water and tipping it out ,
rinsing and tipping until what I was tipping out ran clear. The sole
plate I rubbed at gently with an old green scotch-brite type scourer,
you could try very fine glass paper

I hope that helps some. Does your iron have a help line in the
instruction book or a helpful hints page on the manufacturers website
prahaps.
Claire in Montréal France
http://claireowenperso.free.fr
  #3  
Old April 6th 08, 05:31 AM posted to rec.crafts.textiles.sewing
Just Askin
external usenet poster
 
Posts: 2
Default Problems with a steam iron


"Just Askin" wrote in message
news:[email protected]
I recently bought a brand new Black & Decker Steam Advantage iron (model
F2200). This is one with a "Ceramic Glide" soleplate. I've owned it less
than a week and I am already having problems with it. The specific problem
I am having is that on occasion it is staining my clothes. This happens
when I am ironing over a thick seam, say, the outside corner of the pocket
on the front of a shirt. The iron is leaving a thin, brown stain there.
Sometimes I can brush off what seems to be some residue there, but
sometimes not.

When I examine the soleplate I see some brown stains immediately below the
"top" steam vent, extending in a V-shape in each direction. This stained
area feels slightly rough, as though there is residue there.

Compared with my old iron, which had a non-stick (Teflon?) soleplate, I've
noticed that the ceramic soleplate of this new iron is more "sticky," and
I have to let the steam flow really build up before I can move the iron
back and forth easily. This soleplate also seems to get hotter at a given
fabric heat/steam setting.

I have ironed almost exclusively dress shirts, both 100% cotton and
poly/cotten shirts, with this iron. I am using the recommended heat/steam
setting for the fabric. I have been filling the iron with store-bought,
distilled water.

I have two questions:

(1) What is causing this problem? Is the recommended setting too hot?
Is this residue microscopic, burned, fabric particles?

(2) How can I clean this material off the soleplate?

Thanks in advance. I saw from searching Google that problems with steam
irons have been discussed in this group in the past.


I solved this problem on my own by researching various solutions on the
Internet and trying them until I found one that worked.

This problem was being caused by the fact that this new iron gets quite a
bit hotter than my old iron. In essence, the cotton heat/steam setting is
too hot for the cotten/polyester blend shirts I usually wear. This new iron
is getting so hot that it is, at the microscopic level, burning/melting the
fabric and this burned/melted material is accumulating on the bottom of the
iron. Enough of this residue had collected on the soleplate so that, after
about the fifth time I used the iron, some rubbed off on the shirt I was
ironing, creating the stains I mentioned earlier.

I tried several methods to remove this residue from the soleplate. The one
that worked was making a thick paste of water and baking soda and spooning
some of this on a Scotch Brite "Dobie" scouring pad, then gently scouring
the soleplate in a circular motion. It took about a half-hour to get all
the residue off the soleplate, but I did not scratch the ceramic surface.

I then experimented with lowering the temperature of my iron by setting it
to the next highest setting, the "Wool" setting. This was hot enough to
iron the cotten/poly shirts successfully without causing the burn/melting
problems.

I'm still trying to find a way to get the brown stains out of the shirt that
I was ironing when I discovered the problem. Today I tried a "Magic Wand"
stain remover stick. I rubbed this on the stains than laundered. It may
have removed a little bit, but the stains were still there after laundering.






  #4  
Old February 1st 09, 08:22 PM posted to rec.crafts.textiles.sewing
slavetoironing
external usenet poster
 
Posts: 1
Default Problems with a steam iron

slavetoironing had written this in response to
http://www.sewgirls.com/textiles/Pro...iron-3516-.htm :

Just Askin wrote:


I recently bought a brand new Black & Decker Steam Advantage iron
(model
F2200). This is one with a "Ceramic Glide" soleplate. I've
owned it less
than a week and I am already having problems with it. The specific
problem
I am having is that on occasion it is staining my clothes. This
happens
when I am ironing over a thick seam, say, the outside corner of the
pocket
on the front of a shirt. The iron is leaving a thin, brown stain
there.
Sometimes I can brush off what seems to be some residue there, but
sometimes
not.


When I examine the soleplate I see some brown stains immediately below
the
"top" steam vent, extending in a V-shape in each direction.
This stained
area feels slightly rough, as though there is residue there.


Compared with my old iron, which had a non-stick (Teflon?) soleplate,
I've
noticed that the ceramic soleplate of this new iron is more
"sticky," and I
have to let the steam flow really build up before I can move the iron
back
and forth easily. This soleplate also seems to get hotter at a given
fabric
heat/steam setting.


I have ironed almost exclusively dress shirts, both 100% cotton and
poly/cotten shirts, with this iron. I am using the recommended
heat/steam
setting for the fabric. I have been filling the iron with
store-bought,
distilled water.


I have two questions:


(1) What is causing this problem? Is the recommended setting too hot?
Is
this residue microscopic, burned, fabric particles?


(2) How can I clean this material off the soleplate?


Thanks in advance. I saw from searching Google that problems with
steam
irons have been discussed in this group in the past.






-------------------------------------
I've had similar probs, the sodium bicarb paste did the job or removing
rhe residue. it came away so easily, just used the paste on some damp
kitchen role and it came right off. the secret of the iron is 2 use it 2
settings below the fabric your ironing so silk is good for cotton.




##-----------------------------------------------##
Delivered via http://www.sewgirls.com/
Sewing Community of the Net
Web and RSS access to your favorite newsgroup -
rec.crafts.textiles.sewing - 3757 messages and counting!
##-----------------------------------------------##
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Steam Iron Rant John Quilting 16 September 22nd 07 02:42 PM
FS: Vintage Singer Featherweight Iron -- Best Piecing Iron Available! singer_fw_iron_lover Marketplace 0 August 14th 04 08:10 PM
FS: Vintage Singer Featherweight Iron -- Best Piecing Iron Available! singer_fw_iron_lover Marketplace 0 August 14th 04 08:09 PM
iron on transfer ruined iron??? Sharon Gates Quilting 5 November 1st 03 08:32 PM


All times are GMT +1. The time now is 07:40 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©2004-2018 CraftBanter.
The comments are property of their posters.