If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
New Kiln
Hello All:
I am very new to this stuff and could use some pointers, but last week I came across a great deal on a kiln and wheel. The kiln has never been assembled, it is about 30 years old, it was sold by Westby Ceramic supply and is 4 rows of 8 bricks each, 3 rows have heating elements and one row is a spacer row. I don't know where the spacer row is supposed to be located in the stack, or if it even maters where it is placed. I had to lay out bricks and trace the ring on them and cut the bricks to shape for the lid and base of the thing. It's all held together with bands, 2 for each ring and one for the lid and one for the base. Now I need to coat the lid and base with this mortar stuff that is in the kit and install the coils and wiring. The wiring is asbestos covered so I don't want to mess with it. What do kilns use now a days for wire that will hold up to the heat? Does anyone have info or experience with one of these kilns? Also the wheel that I got is called a spinning tiger. It is missing the rubber drive thing on the motor shaft so I ordered one from Creative supply, it seemed awfully expensive for a piece of rubber, It doubled my cost for the whole outfit!, I got the kiln, Wheel and a box of clay for $25. Anyhow, please post any helpful comments that you may have, Thanks, Brian |
Ads |
#2
|
|||
|
|||
i hav eno clue as to how to assempble it but my 1st question is are you
complainging about the price or bragging ) as for the asbestos wireing it will need to be takes and disposed of at a hazardous materials site. check with a local suppy hous eon wireing and information. I would recomend www.kickwheel.com in atlanta or davens i forget their email address. the heating elements i woudl imagine are probably ok but if not i think they could recomend some replacements for you also. "Democracy is two wolves and a lamb voting on what to have for lunch. Liberty is a well-armed lamb contesting the vote." -- Benjamin Franklin, 1759 |
#3
|
|||
|
|||
Thanks for that info Dave, I bagged and got rid of the asbestos last
night. It appears that the big difference between mine and the new kilns is that the electrical box's on them have an air gap of about 1/2 inch between the brick and the box, "mine would have been screwed directly to the side without an air gap. One thing that I found out at Seattle pottery was that most, if not all, of the new kilns have all the heating coils on one circuit, like they all come on at the same time. Mine is set up as 3 separate circuits originally but since I have to wire the whole thing anyway I will hook all the heaters to one circuit. That is unless the people on this NG say it's better one way or the other. Thanks for the help and please keep it coming, Bri David Coggins wrote: Hi Brian, Your bargain kiln sounds very old, but should be OK. There are still lots of kilns that age in regular use. Toss the asbestos covered wire away. For high temperature connections, you cannot use copper wire - the wire must be multi stranded nickel alloy. There is a high temperature silicone insulated wire available to use on kiln wiring, with or without braided sheath, which has the necessary multistrand wiring. It is available from most kiln manufacturers, or you might get some from a specialist wire store. If the elements are new, there should be no problem fitting them to the kiln, you can stretch or bend the wire without problems, until it is fired. Then it becomes very brittle, and can't be moved unless it is red hot. Dave -- "Bri" wrote in message ... Hello All: I am very new to this stuff and could use some pointers, but last week I came across a great deal on a kiln and wheel. The kiln has never been assembled, it is about 30 years old, it was sold by Westby Ceramic supply and is 4 rows of 8 bricks each, 3 rows have heating elements and one row is a spacer row. I don't know where the spacer row is supposed to be located in the stack, or if it even maters where it is placed. I had to lay out bricks and trace the ring on them and cut the bricks to shape for the lid and base of the thing. It's all held together with bands, 2 for each ring and one for the lid and one for the base. Now I need to coat the lid and base with this mortar stuff that is in the kit and install the coils and wiring. The wiring is asbestos covered so I don't want to mess with it. What do kilns use now a days for wire that will hold up to the heat? Does anyone have info or experience with one of these kilns? Also the wheel that I got is called a spinning tiger. It is missing the rubber drive thing on the motor shaft so I ordered one from Creative supply, it seemed awfully expensive for a piece of rubber, It doubled my cost for the whole outfit!, I got the kiln, Wheel and a box of clay for $25. Anyhow, please post any helpful comments that you may have, Thanks, Brian |
#4
|
|||
|
|||
I would keep the wiring as three separate circuits. It gives more control of
temperature - in other words you can put more heat into the bottom or the top, depending on how evenly the kiln fires, or how evenly the kiln is loaded. Secondly, you might overload the control switch if you ran all the element through the one switch. Dave "Bri" wrote in message ... One thing that I found out at Seattle pottery was that most, if not all, of the new kilns have all the heating coils on one circuit, like they all come on at the same time. Mine is set up as 3 separate circuits originally but since I have to wire the whole thing anyway I will hook all the heaters to one circuit. That is unless the people on this NG say it's better one way or the other. Thanks for the help and please keep it coming, Bri |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Important - Please beware of a company called Bohle | Eric Russell | Glass | 2 | August 23rd 04 07:46 PM |
Fusing/slumping/casting with kiln sitter | Gordon Watt | Glass | 13 | December 11th 03 03:46 PM |
Good news, and agonizing over kiln purchase | Kalera Stratton | Beads | 0 | October 14th 03 06:11 PM |
F/A @ EBAY Electric Kiln | BATMAN.ROBIN | Marketplace | 0 | September 17th 03 10:51 PM |
Kiln question | Kalera Stratton | Beads | 13 | July 11th 03 06:35 AM |