![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
Hi,
Does anyone know of a newsgroup dedicated strickly to ceramics and not pottery? Thanks, Steve |
Ads |
#2
|
|||
|
|||
![]()
On Fri, 19 Dec 2003 19:40:01 -0500, "Steve Holcomb"
wrote: Does anyone know of a newsgroup dedicated strickly to ceramics and not pottery? What is your definition of "ceramics"? deg |
#3
|
|||
|
|||
![]() Steve Holcomb wrote: Hi,Does anyone know of a newsgroup dedicated strickly to ceramics and not pottery? what is in your opinion the difference between ceramics and pottery? Monika -- Monika Schleidt www.schleidt.org/mskeramik |
#4
|
|||
|
|||
![]()
On Fri, 19 Dec 2003 19:40:01 -0500, "Steve Holcomb"
wrote: This is a multi-part message in MIME format. ------=_NextPart_000_0036_01C3C667.E4841B60 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Hi, Does anyone know of a newsgroup dedicated strickly to ceramics and not = pottery? Thanks, Steve If you mean "ceramics" in the technical sense as a material or technology and not as a craft involving painting glaze on bisqued puppy dogs and angels, then sci.materials.ceramics is the only one I know of. However, it gets *very* little traffic, probably less than one post per week unless someone comes up with an interesting problem. Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com |
#5
|
|||
|
|||
![]()
I was amused to see your sig. I have 3 or 4 working dt2821 boards sitting
in my store room that I once used for speech research. For reasons I can no longer remember we moved on to a DAQ board..... I cannot face the idea of giving up the boards because they were so expensive but hate seeing them not put to use.... Is there a market for these anymore? DKat "Bob Masta" wrote in message ... On Fri, 19 Dec 2003 19:40:01 -0500, "Steve Holcomb" wrote: This is a multi-part message in MIME format. ------=_NextPart_000_0036_01C3C667.E4841B60 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Hi, Does anyone know of a newsgroup dedicated strickly to ceramics and not = pottery? Thanks, Steve If you mean "ceramics" in the technical sense as a material or technology and not as a craft involving painting glaze on bisqued puppy dogs and angels, then sci.materials.ceramics is the only one I know of. However, it gets *very* little traffic, probably less than one post per week unless someone comes up with an interesting problem. Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com |
#6
|
|||
|
|||
![]()
On Tue, 24 Feb 2004 16:37:05 -0500, "D Kat"
wrote: I was amused to see your sig. I have 3 or 4 working dt2821 boards sitting in my store room that I once used for speech research. For reasons I can no longer remember we moved on to a DAQ board..... I cannot face the idea of giving up the boards because they were so expensive but hate seeing them not put to use.... Is there a market for these anymore? DKat I don't know about a "market" for them, but they can be used with my Daqarta software in real-mode DOS. (Win9X or earlier.) The DT2821 was the grandaddy of all data acquisition boards, and really was amazing in its day. But they did things in a lot of ways that are downright screwy by more modern standards. It was by far the hardest board I've ever written a driver for. (However, I was also making it do tricks that the manufacturer said it couldn't do, like simultaneous input and output.) It would be a great kiln controller as far as resolution goes (12 bits), but its just too darn hard to program. If you count your time for anything, it might be cheaper in the long run to use another board. Or use my (shameless plug) Daqarta software with them and you have a scope/ spectrum / spectrogram analyzer... no obvious application to pottery, but you can make some great voiceprints! (And you are putting an old ISA-bus computer to work instead of sending it to the landfill.) Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
[FAQ] Posting and Advertising Guidelines for rec.crafts.jewelry | [email protected] | Jewelry | 0 | May 27th 04 07:00 AM |
[FAQ] Posting and Advertising Guidelines for rec.crafts.jewelry | [email protected] | Jewelry | 0 | April 23rd 04 07:38 AM |
[FAQ] Posting and Advertising Guidelines for rec.crafts.jewelry | [email protected] | Jewelry | 0 | February 17th 04 03:31 PM |
[FAQ] Posting and Advertising Guidelines for rec.crafts.jewelry | [email protected] | Jewelry | 1 | February 15th 04 10:05 PM |
Pottery or Ceramics Marketplace Newsgroup??? | Katiemae1116 | Pottery | 1 | August 17th 03 03:31 PM |