If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
HEAT RETENTIVE PLATES
Hello,
I have invented a new type of ceramic "heat retentive plate" that you preheat in a microwave oven for just one minute, it stays HOT for 1/2 HOUR and the rim remains cool for easy handling. Please see: http://www.heatstoragedish.com I will answer any questions and teach anyone interested how to make them. The plates are great for steaks, but I use them daily at home for everything. Truly yours! Juan P.S... By the way, I believe this is the first "functional" change to a ceramic plate since the discovery of ceramics in China and Japan in 10,000 BC |
Ads |
#2
|
|||
|
|||
HEAT RETENTIVE PLATES
On 22 Jul 2006 19:41:33 -0700, "Juan" wrote:
Hello, I have invented a new type of ceramic "heat retentive plate" that you preheat in a microwave oven for just one minute, it stays HOT for 1/2 HOUR and the rim remains cool for easy handling. Please see: http://www.heatstoragedish.com I will answer any questions and teach anyone interested how to make them. The plates are great for steaks, but I use them daily at home for everything. Truly yours! Juan P.S... By the way, I believe this is the first "functional" change to a ceramic plate since the discovery of ceramics in China and Japan in 10,000 BC Excellent concept! I for one would be very interested in your method, even if I never made a single plate. I'm guessing maybe some sort of silicon carbide microwave susceptor (judging from the cutaway view shown on your site). But I'm impressed that you can make this work without undue thermal stress on the rest of the plate. Is the susceptor insert perhaps able to move relative to the more-conventional ceramic surrounding plate? From the drawing that looks possible, but I'm mystified how to do that without having it rattle. Good work! And thanks for the offer to share the secret. Best regards, Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com Home of DaqGen, the FREEWARE signal generator |
#3
|
|||
|
|||
HEAT RETENTIVE PLATES
bob, sounds like a scam to buy his plate. much like a perpetual motion
machine. if a plate retained heat so well, it wouldn't do much good in keeping steaks warm either. take a brick out of a raku kiln for 1 hour & you'll see a good deal of heat "retained" lost to understand the scale of his claim. it'll reach room temp in an hour, maybe 1/2 hour. THAT's from 1800F... AND it'll keep steaks warm... now, pull anything from say 400F out & leave it sit. ~ room temp pretty quick. (even zapped in a micro) the claim doesn't make sense in the heattransfer world which is why no such device has been discovered in 10,000 years... unless it's an exceptional insulator which doesn't keep steaks warm. see ya steve Bob Masta wrote: On 22 Jul 2006 19:41:33 -0700, "Juan" wrote: Hello, I have invented a new type of ceramic "heat retentive plate" that you preheat in a microwave oven for just one minute, it stays HOT for 1/2 HOUR and the rim remains cool for easy handling. Please see: http://www.heatstoragedish.com I will answer any questions and teach anyone interested how to make them. The plates are great for steaks, but I use them daily at home for everything. Truly yours! Juan P.S... By the way, I believe this is the first "functional" change to a ceramic plate since the discovery of ceramics in China and Japan in 10,000 BC Excellent concept! I for one would be very interested in your method, even if I never made a single plate. I'm guessing maybe some sort of silicon carbide microwave susceptor (judging from the cutaway view shown on your site). But I'm impressed that you can make this work without undue thermal stress on the rest of the plate. Is the susceptor insert perhaps able to move relative to the more-conventional ceramic surrounding plate? From the drawing that looks possible, but I'm mystified how to do that without having it rattle. Good work! And thanks for the offer to share the secret. Best regards, Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com Home of DaqGen, the FREEWARE signal generator |
#5
|
|||
|
|||
HEAT RETENTIVE PLATES
Bob Masta wrote:
On 23 Jul 2006 05:51:50 -0700, "steve " wrote: bob, sounds like a scam to buy his plate. much like a perpetual motion machine. if a plate retained heat so well, it wouldn't do much good in keeping steaks warm either. I don't see him claiming anything that violates any laws of physics. A plate is a big mass, relative to the food you put on it. If you put food on a cold plate, the food will cool down faster than if you put it on a warm plate, because the food is transferring heat to the plate due to the temperature difference. As I understand his design, it just reverses the situation so the plate is as hot as or hotter than the food. As a bonus, the plate apparently has embedded in it a big slug of some substance that heats up via microwaves. That extra mass will further extend the temperature decay time. Nothing tricky about that, it's just like heating a heavy plate in a conventional oven before you serve the food. His invention is all about heating it quickly in the microwave, without cracking the plate. Best regards, Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com Home of DaqGen, the FREEWARE signal generator Yes, but the mass of the "energy reservoir" will - by definition - require a large amount of energy to heat it up sufficiently. Whether it is possible for this to be practical will depend on whether a standard microwave oven could lead to the absorption of sufficient energy in 1 minute to provide a sufficient reservoir of energy to maintain the plate's temperature for eg 30 minutes. Also it needs to be borne in mind that the "standard" part of the plate will not be heated by the microwave energy and therefore the internal reservoir also needs to provide sufficient energy to bring the rest of the plate up to its "hot" condition. I'm far from convinced ! pHIL |
#6
|
|||
|
|||
HEAT RETENTIVE PLATES
Hi Bob,
It does not rattle because the separation between the pointed bosses and the heater is only about 1 millimeter, the susceptor is simply iron particles and red earthenware. I can say it because the patent will be published in a couple months, it won't be a secret anymore. the market is huge. Juan Bob Masta wrote: On 22 Jul 2006 19:41:33 -0700, "Juan" wrote: Hello, I have invented a new type of ceramic "heat retentive plate" that you preheat in a microwave oven for just one minute, it stays HOT for 1/2 HOUR and the rim remains cool for easy handling. Please see: http://www.heatstoragedish.com I will answer any questions and teach anyone interested how to make them. The plates are great for steaks, but I use them daily at home for everything. Truly yours! Juan P.S... By the way, I believe this is the first "functional" change to a ceramic plate since the discovery of ceramics in China and Japan in 10,000 BC Excellent concept! I for one would be very interested in your method, even if I never made a single plate. I'm guessing maybe some sort of silicon carbide microwave susceptor (judging from the cutaway view shown on your site). But I'm impressed that you can make this work without undue thermal stress on the rest of the plate. Is the susceptor insert perhaps able to move relative to the more-conventional ceramic surrounding plate? From the drawing that looks possible, but I'm mystified how to do that without having it rattle. Good work! And thanks for the offer to share the secret. Best regards, Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com Home of DaqGen, the FREEWARE signal generator |
#7
|
|||
|
|||
HEAT RETENTIVE PLATES
Hi Steve, it is not a scam, the trick is releasing the heat at a
controlled rate according to the stefan-Boltzmann law., it is not based on insulation but containing the radiation in a tight cavity. If the surrounding temperature of the radiating body is high enough, it will contain the radiation.go to this site, look for radiation, then stefan-boltzmann and look at the formula.. if you have more questions (doubts) please let me know. http://hyperphysics.phy-astr.gsu.edu/hbase/hframe.html Juan steve wrote: bob, sounds like a scam to buy his plate. much like a perpetual motion machine. if a plate retained heat so well, it wouldn't do much good in keeping steaks warm either. take a brick out of a raku kiln for 1 hour & you'll see a good deal of heat "retained" lost to understand the scale of his claim. it'll reach room temp in an hour, maybe 1/2 hour. THAT's from 1800F... AND it'll keep steaks warm... now, pull anything from say 400F out & leave it sit. ~ room temp pretty quick. (even zapped in a micro) the claim doesn't make sense in the heattransfer world which is why no such device has been discovered in 10,000 years... unless it's an exceptional insulator which doesn't keep steaks warm. see ya steve Bob Masta wrote: On 22 Jul 2006 19:41:33 -0700, "Juan" wrote: Hello, I have invented a new type of ceramic "heat retentive plate" that you preheat in a microwave oven for just one minute, it stays HOT for 1/2 HOUR and the rim remains cool for easy handling. Please see: http://www.heatstoragedish.com I will answer any questions and teach anyone interested how to make them. The plates are great for steaks, but I use them daily at home for everything. Truly yours! Juan P.S... By the way, I believe this is the first "functional" change to a ceramic plate since the discovery of ceramics in China and Japan in 10,000 BC Excellent concept! I for one would be very interested in your method, even if I never made a single plate. I'm guessing maybe some sort of silicon carbide microwave susceptor (judging from the cutaway view shown on your site). But I'm impressed that you can make this work without undue thermal stress on the rest of the plate. Is the susceptor insert perhaps able to move relative to the more-conventional ceramic surrounding plate? From the drawing that looks possible, but I'm mystified how to do that without having it rattle. Good work! And thanks for the offer to share the secret. Best regards, Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com Home of DaqGen, the FREEWARE signal generator |
#8
|
|||
|
|||
HEAT RETENTIVE PLATES
steve,
I forgot, you can't buy them, I have the only working prototypes. By the way, If you prehea t them for 1:15 minutes, they remain HOT FOR 45 MINUTES.(140deg. F after that time). I can teach you to make them.or rather post so that everybody learns. just let me know. Juan steve wrote: bob, sounds like a scam to buy his plate. much like a perpetual motion machine. if a plate retained heat so well, it wouldn't do much good in keeping steaks warm either. take a brick out of a raku kiln for 1 hour & you'll see a good deal of heat "retained" lost to understand the scale of his claim. it'll reach room temp in an hour, maybe 1/2 hour. THAT's from 1800F... AND it'll keep steaks warm... now, pull anything from say 400F out & leave it sit. ~ room temp pretty quick. (even zapped in a micro) the claim doesn't make sense in the heattransfer world which is why no such device has been discovered in 10,000 years... unless it's an exceptional insulator which doesn't keep steaks warm. see ya steve Bob Masta wrote: On 22 Jul 2006 19:41:33 -0700, "Juan" wrote: Hello, I have invented a new type of ceramic "heat retentive plate" that you preheat in a microwave oven for just one minute, it stays HOT for 1/2 HOUR and the rim remains cool for easy handling. Please see: http://www.heatstoragedish.com I will answer any questions and teach anyone interested how to make them. The plates are great for steaks, but I use them daily at home for everything. Truly yours! Juan P.S... By the way, I believe this is the first "functional" change to a ceramic plate since the discovery of ceramics in China and Japan in 10,000 BC Excellent concept! I for one would be very interested in your method, even if I never made a single plate. I'm guessing maybe some sort of silicon carbide microwave susceptor (judging from the cutaway view shown on your site). But I'm impressed that you can make this work without undue thermal stress on the rest of the plate. Is the susceptor insert perhaps able to move relative to the more-conventional ceramic surrounding plate? From the drawing that looks possible, but I'm mystified how to do that without having it rattle. Good work! And thanks for the offer to share the secret. Best regards, Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com Home of DaqGen, the FREEWARE signal generator |
#9
|
|||
|
|||
HEAT RETENTIVE PLATES
Thank you, they really work, I use them every day, I also have coffe
mugs, those were a piece of cake after solving the problem of thermal shock in the plates. Steve Mills wrote: Juan, I wish you all success with this. If in fact you have invented *the better mousetrap* as the saying goes, it should really run! Steve Bath UK In article . com, Juan writes Hello, I have invented a new type of ceramic "heat retentive plate" that you preheat in a microwave oven for just one minute, it stays HOT for 1/2 HOUR and the rim remains cool for easy handling. Please see: http://www.heatstoragedish.com I will answer any questions and teach anyone interested how to make them. The plates are great for steaks, but I use them daily at home for everything. Truly yours! Juan P.S... By the way, I believe this is the first "functional" change to a ceramic plate since the discovery of ceramics in China and Japan in 10,000 BC -- Steve Mills Bath UK |
#10
|
|||
|
|||
HEAT RETENTIVE PLATES
Bob,
The trick is not only the mass of the heater or susceptor inside the plate, but how efficient it is to capture microwave energy very fast and how it is released at a controlled rate. I capture about 1200 Watts minutes of energy and release it at the rate of about 37.5 watts per minute, that is like having a light bulb of 37.5 Watts inside your plate. Could you post this to all your groups? I'm new to this. I will really appreciate it. Juan Bob Masta wrote: On 23 Jul 2006 05:51:50 -0700, "steve " wrote: bob, sounds like a scam to buy his plate. much like a perpetual motion machine. if a plate retained heat so well, it wouldn't do much good in keeping steaks warm either. I don't see him claiming anything that violates any laws of physics. A plate is a big mass, relative to the food you put on it. If you put food on a cold plate, the food will cool down faster than if you put it on a warm plate, because the food is transferring heat to the plate due to the temperature difference. As I understand his design, it just reverses the situation so the plate is as hot as or hotter than the food. As a bonus, the plate apparently has embedded in it a big slug of some substance that heats up via microwaves. That extra mass will further extend the temperature decay time. Nothing tricky about that, it's just like heating a heavy plate in a conventional oven before you serve the food. His invention is all about heating it quickly in the microwave, without cracking the plate. Best regards, Bob Masta dqatechATdaqartaDOTcom D A Q A R T A Data AcQuisition And Real-Time Analysis www.daqarta.com Home of DaqGen, the FREEWARE signal generator |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Soldering revisited | Snaggeltooth | Jewelry | 7 | March 26th 06 06:24 PM |
Progress in spite of heat | Debra | Quilting | 12 | August 1st 05 11:06 PM |
OT - Story - In Praise of Central Heat | Kathy N-V | Beads | 7 | January 10th 05 05:23 AM |
Question About Cutting Ceramic Plates | R. Seed | Glass | 9 | June 20th 04 08:33 PM |
Heat Setting (DH's ~ you got to love 'em) | Charlotte Hippen | Quilting | 3 | August 20th 03 01:51 PM |