If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Help! Steam a Seam
I just fused an applique with Steam a Seam II Lite where I didn't want it.
It peeled off after heating with an iron, but there's lots of residue left. Any ideas how to get rid of the residue? I know, I should have made certain it was where I wanted it before I fused it - but, that just is NOT how I operate (most of the time)! -- Donna Aten, Coordinator Project Linus - Boise/SW Idaho Chapter Website: www.LinusIdaho.org |
Ads |
#2
|
|||
|
|||
I have some "Goo Off" that is suppose to remove adhesive from fabric. I
think I got it at Joann's -- Mary http://community.webshots.com/user/mardor1948 "Donna in Idaho" (remove spam) wrote in message ... I just fused an applique with Steam a Seam II Lite where I didn't want it. It peeled off after heating with an iron, but there's lots of residue left. Any ideas how to get rid of the residue? I know, I should have made certain it was where I wanted it before I fused it - but, that just is NOT how I operate (most of the time)! -- Donna Aten, Coordinator Project Linus - Boise/SW Idaho Chapter Website: www.LinusIdaho.org |
#3
|
|||
|
|||
I got most (not all) of it off with a combination of finger nail polish
remover & Sol u Mel! I didn't get it on the iron - it's on the fabric! Thanks! -- Donna Aten, Coordinator Project Linus - Boise/SW Idaho Chapter Website: www.LinusIdaho.org "Joan8904" wrote in message ... Run the hot iron over a used 'dryer' softener sheet. Takes the goo right off! joan joan o'reilly Watch your thoughts, they become words. Watch your words they become actions. Watch your actions, they become habits. Watch your habits, they become character. Watch your character it becomes your destiny. |
#4
|
|||
|
|||
Ya know, I think we have some Goo Off - never thought of using that.
-- Donna Aten, Coordinator Project Linus - Boise/SW Idaho Chapter Website: www.LinusIdaho.org "maryd" wrote in message ... I have some "Goo Off" that is suppose to remove adhesive from fabric. I think I got it at Joann's -- Mary http://community.webshots.com/user/mardor1948 "Donna in Idaho" (remove spam) wrote in message ... I just fused an applique with Steam a Seam II Lite where I didn't want it. It peeled off after heating with an iron, but there's lots of residue left. Any ideas how to get rid of the residue? I know, I should have made certain it was where I wanted it before I fused it - but, that just is NOT how I operate (most of the time)! -- Donna Aten, Coordinator Project Linus - Boise/SW Idaho Chapter Website: www.LinusIdaho.org |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Steam Press??? | Maureen Wozniak | Quilting | 5 | February 29th 04 03:06 AM |
Steam and fabric distortion | Jan Dunaway | Quilting | 33 | February 2nd 04 02:43 AM |
seam finish for polar fleece | L. Kelly | Needlework | 0 | September 8th 03 07:15 PM |
"Extra" seam allowance? | Meghan | Quilting | 0 | July 17th 03 02:14 AM |