A crafts forum. CraftBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » CraftBanter forum » Craft related newsgroups » Jewelry
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

heat and emeralds...??? Also undoing bezels and hammerset?



 
 
Thread Tools Display Modes
  #1  
Old May 10th 04, 06:20 AM
Des Bromilow
external usenet poster
 
Posts: n/a
Default heat and emeralds...??? Also undoing bezels and hammerset?

I was just told that heat and emeralds pose a problem for cracking.
Is there a chart or rule of thumb with respect to which stones/ gems can be
heated safely, and which cannot?
I understand that pearls are heat sensitive... would it be fair to say all
"biologically created" gems cannot be heated (ie, pearls, amber)
I've read that diamonds are safe to heat, but what about other minerally
created stones? Is there a rule of thumb regarding opaque versus
translucent?

Beginner's question I know, but I'd be safer knowing than not.

ALSO -
How do I remove a stone from a bezel mount? Is it a process of gently
peeling the bezel back?, or should I cut the bezel away?
How about hammer set?

thanks,
Des

Ads
  #2  
Old May 11th 04, 01:37 AM
Heinrich Butschal
external usenet poster
 
Posts: n/a
Default

Des Bromilow wrote:
I was just told that heat and emeralds pose a problem for cracking.
Is there a chart or rule of thumb with respect to which stones/ gems can be
heated safely, and which cannot?
I understand that pearls are heat sensitive... would it be fair to say all
"biologically created" gems cannot be heated (ie, pearls, amber)
I've read that diamonds are safe to heat, but what about other minerally
created stones? Is there a rule of thumb regarding opaque versus
translucent?

Beginner's question I know, but I'd be safer knowing than not.

ALSO -
How do I remove a stone from a bezel mount? Is it a process of gently
peeling the bezel back?, or should I cut the bezel away?
How about hammer set?

thanks,
Des

I´m sorry it´s german. However You can read more here about casting:
http://schmuckfabrik.de/werkstatt/englisch-index.htm

4. Liste der Edelsteine die eingegossen werden können.:
(List of stones wich might be used in casting process)

Diamanten

Hämatit, schwarz

Jade-Nephrit

Jaspis

Mondstein

Olivin

Peridot

Rubin

Saphir

Spinell

Sternrubin

Sternsaphir

Zirkonia

Liste der Edelsteine die ebenfals eingegossen werden können, bei denen
jedoch das Risiko des Farbumschlages besteht.:

Achat rot, braun und Moosachat Die Farbe wird manchmal schöner

Amethyst

Aquamarin wird manchmal milchig

Diamanten farbig

Granat

Jadeit manchmal grau und weiß

Karneol

Obsidian

Onyx wird normalerweise grau

Rauchquarz kann trüb werden, meist aber hell

Rosenquarz

Smaragd werden heller und bläulich wie Aquamarin

Tigerauge kann hübschen Farbumschlag haben

Topas gelbliche Steine werden rosa

Turmalin rosa Turmaline bleichen aus

Zirkon können manchmal gelb werden, auch beim Löten. Vielleicht durch
Flußmittel

Beim Gießen gilt folgendes zu berücksichtigen:

Diamanten
sind für Oxydation während des Brennvorganges der Küvette empfindlich.
Die Oxydation der Küvette ist aber zur Verbrennung von Rußresten in der
Küvette notwendig. Wichtig ist hier eine Feinabstimmung der
Brennendtemperatur, so daß zwar der Ruß, aber nicht die Diamanten
verbrennen. Diamanten sind kurzfristig (3-5 Minuten) problemlos bis 900
Grad Celsius zu erhitzen ohne daß die geringste Schleierbildung
entsteht. Vom Löten wissen wir daß man dies auch beliebig wiederholen
kann und auch ohne Schutzmittel nichts passiert.

Nur wenn eine Temperatur von ca. 680 Grad oder höher, längere Zeit (bei
750 Grad ab 7 Minuten) mit Luftzufuhr auf Diamanten einwirkt, startet
die stille Oxydation der Diamantoberfläche - der Stein wird zuerst
milchig, dann kleiner und rund.

Ich empfehle daher die höchste Ofentemperatur nicht über 650 Grad
einzustellen, sondern besser 600 Grad als Maximum einzustellen. Eine
enstprechende Verlängerung der Brennzeit ist unproblematisch.

Rubine, Saphire
sind, wenn sie nicht gewachst oder geölt sind, so wie Zirkonia und
Granate bezüglich der Brenntemperatur unempfindlich.

Anders ist die Empfindlichkeit des Edelsteins gegen Temperaturschocks
wie sie beim Umgießen mit dem deutlich heisseren Metall erzeugt wird.

Dann kann es zur ringförmigen Rissbildung in etwa des Tafelrandes kommen.

Um den Temperaturschock so gering wie möglich zu halten sollte:

in die heiße Küvette und mit "kühlen" Legierungen gegossen werden.

Daneben sind die Edelsteine abhängig von Ihrer Wärmeleitfähigkeit
unterschiedlich empfindlich. Kleine Steine sind generell
unproblematischer, lediglich bei größeren Steinen entstehen Rissgefahren.

Diamanten habe ich bis zu 1/2 und 3/4 Karäter problemlos eingegossen.
Erst ein 1-1/3 Karäter hat ringförmige Risse bekommen.

Korunde, die eine geringere Wärmeleitfähigkeit haben, konnte ich nur bis
zu etwa 1/3 Karätern problemlos eingießen.

Zirkonia, mit der schlechtesten Wärmeleitfähigkeit blieben nur bis zu 10
Punkte - Steinen heil.

Nach dem Guß
sollte man die Küvette trocken ausklopfen damit der Gußbaum herausfällt.
Dann sollte man Ihn zum Abkühlen auf Handtemperatur liegen lassen. Erst
dann im Wasser reinigen. Sonst entstehen durch zu schnelles Abkühlen
Risse, die radial von aussen nach innen gehen.





--
www.juwelen.online-boerse.org
www.meister-atelier.de
www.schmuckfabrik.de
www.medico.butschal.de
  #3  
Old May 11th 04, 01:37 AM
NE333RO
external usenet poster
 
Posts: n/a
Default

I was just told that heat and emeralds pose a problem for cracking.

Among other things. Alot are treated also which is a whole nother mess.

Is there a chart or rule of thumb with respect to which stones/ gems can be
heated safely, and which cannot?


Thats a tough one. I have a chart somewhere but don't seem to be able to
dig it up. Generally you can heat diamonds even to the point of retipping them
(gold not platinum) with the stone in place assuming they are not treated.
Sapphires and rubys take a good amount of heat as long as they are not
treated. I'll usually even retip with the stone in place if it's not a big or
expensive stone. Repairs in the vacinity of the stone are generally ok.
Emeralds don't take heat well and are usually expensive. Generally you
don't do repairs with a torch anywhere near the stone.
As a general rule I keep the torch away from anything other than diamond,
sapphire and ruby.

I understand that pearls are heat sensitive... would it be fair to say all
"biologically created" gems cannot be heated (ie, pearls, amber)


Fairly good rule of thumb with the possible exception of petrified wood
(never tried to heat it). They start to burn at very low heats. Being porus you
also have to be careful what you heat sink them in.

ALSO -
How do I remove a stone from a bezel mount? Is it a process of gently
peeling the bezel back?, or should I cut the bezel away?


If you are replacing the stone I'd break it out and then gently push open
the bezel. If you are saving the stone (and it's set properly) you generally
will have a better chance if you cut the bezel. You can try to push it open
with a graver but you tend to tear up the bezel and damage the stone. If it's a
cheap stone, and a standard size, you may find it cheaper to break the stone
and replace it rather than try to push back the bezel. TELL THE CUSTOMER if you
plan to do that.
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 02:55 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 CraftBanter.
The comments are property of their posters.