If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Do you mean "magnet wire", the kind of ultra-thin wire used to wind
electro-magnets? I wouldn't think so, but I'd check its ability to carry the current load you need (typically a couple of hundred milliamps at 12 V.) without getting warm or worse. If you REALLY mean magnetIC wire (wire that's attracted to a magnet) then it would be made out of iron and typically wouldn't be very useful in electrical work. - Herb bambam wrote: Hi, Just wondering if magnetic wire is OK.for use in wiring a dollhouse. Bambam |
Ads |
#2
|
|||
|
|||
On Thu, 9 Oct 2003 21:49:49 -0700, "bambam" wilma@bedrock cafe
wrote: Hi, Just wondering if magnetic wire is OK.for use in wiring a dollhouse. Bambam Magnet wire has a varnish insulation coating which can be difficult to remove. My preferred material is the individual conductors from multi conductor telephone cables as used in commercial installations (ask your phone man) The plastic coating on these wires is easily removed by pulling the wire between finger and thumbnail. If you must purpose buy material, I suspect "wire wrap" wire would work well. Gerry :-)} London, Canada |
#3
|
|||
|
|||
magnetic wire
Hi, Just wondering if magnetic wire is OK.for use in wiring a dollhouse.
Bambam |
#4
|
|||
|
|||
Yes magnet wire,sales person at Radio Shack told me it would work but I had
my doubts. Thank You. "Herb" wrote in message ... Do you mean "magnet wire", the kind of ultra-thin wire used to wind electro-magnets? I wouldn't think so, but I'd check its ability to carry the current load you need (typically a couple of hundred milliamps at 12 V.) without getting warm or worse. If you REALLY mean magnetIC wire (wire that's attracted to a magnet) then it would be made out of iron and typically wouldn't be very useful in electrical work. - Herb bambam wrote: Hi, Just wondering if magnetic wire is OK.for use in wiring a dollhouse. Bambam |
#5
|
|||
|
|||
If it can carry the load it's an interesting approach! You could use
"round-wire" instead of tape but with the advantage of there being no need to route grooves in walls/floors/ceilings, etc. Are you going to try it? To make connections with it, use a little sandpaper at the ends to remove the lacquer insulation. It can be a little awkward to work with - easy to kink and hard to straighten out again. - Herb bambam wrote: Yes magnet wire,sales person at Radio Shack told me it would work but I had my doubts. Thank You. "Herb" wrote in message ... Do you mean "magnet wire", the kind of ultra-thin wire used to wind electro-magnets? I wouldn't think so, but I'd check its ability to carry the current load you need (typically a couple of hundred milliamps at 12 V.) without getting warm or worse. If you REALLY mean magnetIC wire (wire that's attracted to a magnet) then it would be made out of iron and typically wouldn't be very useful in electrical work. - Herb bambam wrote: Hi, Just wondering if magnetic wire is OK.for use in wiring a dollhouse. Bambam |
#6
|
|||
|
|||
Yes,I think I'll hook up a string of lights with it and see how warm it
gets. "Herb" wrote in message ... If it can carry the load it's an interesting approach! You could use "round-wire" instead of tape but with the advantage of there being no need to route grooves in walls/floors/ceilings, etc. Are you going to try it? To make connections with it, use a little sandpaper at the ends to remove the lacquer insulation. It can be a little awkward to work with - easy to kink and hard to straighten out again. - Herb bambam wrote: Yes magnet wire,sales person at Radio Shack told me it would work but I had my doubts. Thank You. "Herb" wrote in message ... Do you mean "magnet wire", the kind of ultra-thin wire used to wind electro-magnets? I wouldn't think so, but I'd check its ability to carry the current load you need (typically a couple of hundred milliamps at 12 V.) without getting warm or worse. If you REALLY mean magnetIC wire (wire that's attracted to a magnet) then it would be made out of iron and typically wouldn't be very useful in electrical work. - Herb bambam wrote: Hi, Just wondering if magnetic wire is OK.for use in wiring a dollhouse. Bambam |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Wire Density Questions | Karen Chan | Beads | 2 | August 29th 04 06:24 PM |
AD: Wire Sculpture Jewelry videos on eBay & Accounting | Magik | Beads | 2 | June 21st 04 10:31 PM |
Wire question | Regina | Beads | 2 | November 23rd 03 08:53 PM |
Wire Wrapping instead of jumprings...funny tools | April H. | Beads | 13 | September 12th 03 06:14 PM |
I need beads! Rant and ? about wire | mkahogan | Beads | 6 | July 23rd 03 02:06 AM |