If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
incorporating wood?
I'm thinking of doing a lead came panel using some thin slabs of wood
as the "glass pieces," mixed in with the regular glass pieces. I can slice them with my band saw no prob, but I'm wondering, anybody has any suggestions what kind of goop I can slop on the wood? Looking for something that doesn't soak in but it being there to protect other stuff from doing so (solder flux, putty, cleanenmup stuff etc.) and once the panel is all done, I could just peel it off and then oil finish the wood slabs to get the grain to show. I'd greatly appreciate any clues you might come up with, Bart. - Check my most up to date email address at: www.haruteq.com/contact.htm custom compensated banjo bridges, tabs, stained glass: www.haruteq.com **may your moments of need be met by moments of compassion** |
Ads |
#2
|
|||
|
|||
Clear contact paper?
"Bart V" wrote in message ... I'm thinking of doing a lead came panel using some thin slabs of wood as the "glass pieces," mixed in with the regular glass pieces. I can slice them with my band saw no prob, but I'm wondering, anybody has any suggestions what kind of goop I can slop on the wood? Looking for something that doesn't soak in but it being there to protect other stuff from doing so (solder flux, putty, cleanenmup stuff etc.) and once the panel is all done, I could just peel it off and then oil finish the wood slabs to get the grain to show. I'd greatly appreciate any clues you might come up with, Bart. - Check my most up to date email address at: www.haruteq.com/contact.htm custom compensated banjo bridges, tabs, stained glass: www.haruteq.com **may your moments of need be met by moments of compassion** |
#3
|
|||
|
|||
ever use penetrol? it would probably keep the wood nice from start to finish
with out having to peel off anything or oil the wood??? Use care with the stuff tho, as it tends to spontaneously combust while liquid. Once dry, no problem. May be worth a test anyway. m "Bart V" wrote in message ... I'm thinking of doing a lead came panel using some thin slabs of wood as the "glass pieces," mixed in with the regular glass pieces. I can slice them with my band saw no prob, but I'm wondering, anybody has any suggestions what kind of goop I can slop on the wood? Looking for something that doesn't soak in but it being there to protect other stuff from doing so (solder flux, putty, cleanenmup stuff etc.) and once the panel is all done, I could just peel it off and then oil finish the wood slabs to get the grain to show. I'd greatly appreciate any clues you might come up with, Bart. - Check my most up to date email address at: www.haruteq.com/contact.htm custom compensated banjo bridges, tabs, stained glass: www.haruteq.com **may your moments of need be met by moments of compassion** |
#4
|
|||
|
|||
The only thing I can think of that would be reliable at the temps involved
would be thin aluminum foil (regular kitchen not heavy duty.) I would finish the wood first then use a thin coat of rubber cement to hold the foil to the wood. The foil would disipate the heat of soldering and cover for chemicals. You would have to do the rubber cement after finishing because I think it will interfere with the finishing if applied to the bare wood. -- Mike Firth Hot Glass Bits Furnace Working Website http://users.ticnet.com/mikefirth/hotbit46.htm Latest notes "Bart V" wrote in message ... I'm thinking of doing a lead came panel using some thin slabs of wood as the "glass pieces," mixed in with the regular glass pieces. I can slice them with my band saw no prob, but I'm wondering, anybody has any suggestions what kind of goop I can slop on the wood? Looking for something that doesn't soak in but it being there to protect other stuff from doing so (solder flux, putty, cleanenmup stuff etc.) and once the panel is all done, I could just peel it off and then oil finish the wood slabs to get the grain to show. I'd greatly appreciate any clues you might come up with, Bart. - Check my most up to date email address at: www.haruteq.com/contact.htm custom compensated banjo bridges, tabs, stained glass: www.haruteq.com **may your moments of need be met by moments of compassion** |
#5
|
|||
|
|||
Ask this guy.
http://www.holtenwood.bc.ca/studios/vmdoor1.htm He does post on other boards and seems pretty knowledgable about technical things. |
#6
|
|||
|
|||
or you might try lead...
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
when is wood dry | holmsy | Carving | 8 | February 1st 05 08:08 AM |
Type of wood for doll house/components | carino | Doll Houses | 6 | May 14th 04 08:03 PM |
is this all about Wood, or are there Stone carvers here too? | RainLover | Carving | 5 | October 28th 03 08:03 PM |
Using wood pieces... | Bart V | Glass | 10 | September 24th 03 02:30 AM |
3-D Wood Carving Machine | A.T. | Carving | 0 | August 28th 03 05:39 AM |