If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
safe disposal of chemicals
Hi. I just bought a house in the woods. The garage is a separate
building, and I intend to set up a small metalworking shop to augment my woodworking -- I just graduated from school where I fell in love with metalsmithing while being a furniture major ... I especially love making small vessels & objects. The main problem is that there's no running water in the space, and no drainage pipes leading to my septic tank. The chemicals I use are silver, copper & nickel pickles, acid etching chems, patinas, and sometimes photography chemicals. Without spending a lot of $$, I figure I can set up a sink and feed it with a gardening hose -- I can do this easily right outside the garage's back door. But then I need to catch the runoff and dispose of it somehow. I don't really want to introduce this stuff into my septic tank, and feel uncomfortable with dumping it onto my hillside, even if I were to build a greywater system. I suppose I can dispose of it at the dump, but I'm lazy and would like to avoid that!!! Of course the long term solution would be to get a separate septic tank installed, or get a greywater sink that has a built-in filter, but that's going to take me a while to afford. Meanwhile, does anyone out there have similar circumstances? How do you deal with it? Does anyone know for sure the relative toxicity of the chems, and if neutralizing them with baking soda is enough to make it safe for a greywater system? I read on a previous thread about a woman who uses Spa Up (spa/pool chemical) instead of pickle -- is it really safer? Does it work for all metals? As with my woodworking, I want my metalworking to be as "green" as possible. Any comments on this issue would be appreciated! Thanks! lisau |
Ads |
#2
|
|||
|
|||
|
#3
|
|||
|
|||
"lisau" wrote: (clip) I want my metalworking to be as "green" as possible. Any comments on this issue would be appreciated! (clip) ^^^^^^^^^^ Where I used to work we sold a system which could help you. It consisted of a metal 5-gal pail with a heater wrapped around the outside. It had a close-fitting plastic cover with a small fan, blowing air across the contents into a duct to the outside. You would empty your nasty water based chemical solutions into the can and just wait for the heat/air flow to reduce them to a dry concentrate. When the can got full, it went to a toxic waste disposal service. I don't know whether this lash-up is still on the market, but I don't think it would be hard to build one, and a lot cheaper, at that. |
#4
|
|||
|
|||
"Peter W. Rowe" wrote in message
news Safer pickles, though considerably slower, can be made with weaker acids. Citric acid, which can be purchased as a food grade chemical, works reasonably well, especially with silver and gold work. Less effective with the thicker oxides you get on copper, but it can still work, if you're willing to give it more time to work. I've had luck with the classic vinegar + salt solution. Even etches the surface of the (brass/bronze/copper) and shows a crystalline appearance... oh, castings BTW. All the worse though since you guys are just soldering, I'm melting the whole thing. (Unless you're casting a ring or something of course, but then agian, I don't do things as small. Tim -- "I've got more trophies than Wayne Gretsky and the Pope combined!" - Homer Simpson Website @ http://webpages.charter.net/dawill/tmoranwms |
#5
|
|||
|
|||
Can you clarify your water supply to your home? are you on mains as we
call it here in the UK or do you rely on a spring.? If you rely on aspring etc how many gallons in 24 hrs do you think you can draw? or are you using a well? you need to look at your total water cycle if like me your possibly completly independent for water. IE where yourwater comes from what the flow gradientof the water might be and where it ends up. Ive been a metal craftsman for some 36 years and at my present place for 33. we arewholly independent here also out in the boon docks for all our services so weve had to think very carefully how we treat out own back yard. we have a septic tank too, but my chemical wastes are minimal. Mostly sulfuric acid pickles containing copper and zinc metallic salts. I dispose of say 2 to 3 gallons a year of this into a chalk pit well downstream of any rainwater ditches or near my house. below thepit is clay where the ground water is well below any possibility of leaching into surface ditches . My water supply comes from a spring up hill from the house and comes from a sand water bearing aquifer overlaying clay. This water is affected by the local acidheathland so is acidic in nature. In fact it corrosive to the point that a galvanised tank will lose its zinc coating in about 6 months. So all our plumbing has to be either pure copper or stainless steel. 316 grade. Brass will dezincify in about 5 years. leaving a brittle copper sponge. Never had any infections or ailments in 33 years from the water. Its also quite untreated except for filtration. Peter has covered just about all you need to know. If in any doubt take the waste to your local recycling /dump and ask the manager there what they do with waste acids. At out dump, some 6 miles away, all old car batteries go into a large plastic skip so you could put your acid plastic containes into one of those. lisau wrote: Hi. I just bought a house in the woods. The garage is a separate building, and I intend to set up a small metalworking shop to augment my woodworking -- I just graduated from school where I fell in love with metalsmithing while being a furniture major ... I especially love making small vessels & objects. The main problem is that there's no running water in the space, and no drainage pipes leading to my septic tank. The chemicals I use are silver, copper & nickel pickles, acid etching chems, patinas, and sometimes photography chemicals. Without spending a lot of $$, I figure I can set up a sink and feed it with a gardening hose -- I can do this easily right outside the garage's back door. But then I need to catch the runoff and dispose of it somehow. I don't really want to introduce this stuff into my septic tank, and feel uncomfortable with dumping it onto my hillside, even if I were to build a greywater system. I suppose I can dispose of it at the dump, but I'm lazy and would like to avoid that!!! Of course the long term solution would be to get a separate septic tank installed, or get a greywater sink that has a built-in filter, but that's going to take me a while to afford. Meanwhile, does anyone out there have similar circumstances? How do you deal with it? Does anyone know for sure the relative toxicity of the chems, and if neutralizing them with baking soda is enough to make it safe for a greywater system? I read on a previous thread about a woman who uses Spa Up (spa/pool chemical) instead of pickle -- is it really safer? Does it work for all metals? As with my woodworking, I want my metalworking to be as "green" as possible. Any comments on this issue would be appreciated! Thanks! lisau |
#6
|
|||
|
|||
Or you could build a wetland to take care of your problem.
http://technology.infomine.com/envir...ds/Welcome.htm Shawn "Peter W. Rowe" wrote in message news On , in ìð (lisau) wrote: I don't really want to introduce this stuff into my septic tank, and feel uncomfortable with dumping it onto my hillside Some of these things are safe enough to dump on the ground if there's good absorbtion, which is the same as putting it in the septic tank for most purposes, with small amounts. One can dig a small pit, fill it back up with crushed limestone, and pour DILUTED waste acids in there. The limestone will neutralize it. This works fine for SMALL amounts, when you don't have significant amounts of dissolved toxic metals. neither the copper or silver that might be in there will be that much of a problem. nickel is more toxic. And some of your other chemicals may be also not allowable in the ground as is. You should check with local regulations as well, to find out what's recommended in your area.. Much of the question revolves around the amount of chemical you're needing to dispose of. Much of the time, you're not disposing of chemical, just rinsing an item that's been in an acid cleaning bath, and it's only the runoff you worry about. This can be helped a lot by using a seperate small rinse tank of clear water, which is itself replenished with clean water as evaporation etc requires, and this rinse water is also used to replenish evaporation losses from the main containers. In this way, the amount of "drag out" chemical that actually gets beyond that system into the waste water is almost negligably small for the types of chemicals, in small amounts, that you'll be using. Of course the long term solution would be to get a separate septic tank installed, Again, whether this is a solution depends much on the individual chemicals. remember that a septic system is not a toxic waste treatment facility. Primarily, it's designed to dispose of biodegradable wastes, and little else. Chemical disposal through a septic system simply spreads the chemical out in the septic field, often little changed. Whether this has any effect or consequence depends on the amount and type of the chemical. In some cases, it can kill the biological activity of a septic system, with unpleasant results. or get a greywater sink that has a built-in filter, but that's going to take me a while to afford. Another method of disposing of such things is to simply put it in an open wide container with lots of surface area, protected as needed so children, pets, or others don't get in, etc. Then just let the water content evaporate. Accumulated dry waste chemical would need disposal at local facilities, but would require it much less frequently. Meanwhile, does anyone out there have similar circumstances? How do you deal with it? Does anyone know for sure the relative toxicity of the chems, and if neutralizing them with baking soda is enough to make it safe for a greywater system? Again, it depends on the chemical, and what you've dissolved in it. pickle as used by jewelers to clean oxides from silver, gold, or copper alloys, is generally fairly safe when dilute. Baking soda can neutralize it, as can the aformentioned limestone filled pit, but neither does anything to dissolved metallic contents, which may or may not present a problem, depending on which metal and how much there is. Your photo chemicals may be more of a problem, as can be some etching solutions. I read on a previous thread about a woman who uses Spa Up (spa/pool chemical) instead of pickle -- is it really safer? Does it work for all metals? Use "spa down", not spa up. What you're looking for is sodium bisulphate, which is a sulphuric acid salt. It is safer than using an actual sulphuric acid pickle. Note that buying this as the pool chemical is only a means to save money. It's the same chemical as is sold by jewelry supply houses as normal pickling chemical for silver, copper, or gold work. It has the advantage of being lower priced as the pool chemical, as well as, oddly, being purer when purchased in this form. Some of the brands (Sparex especially) of commercial pickle are quite impure, and mess up your container more quickly. As I said, this stuff is safer than Actual sulphuric acid, but it still can burn holes in clothing, and fumes from the stuff when hot/boiling, in a closed unventilated space, are not so good. Safer pickles, though considerably slower, can be made with weaker acids. Citric acid, which can be purchased as a food grade chemical, works reasonably well, especially with silver and gold work. Less effective with the thicker oxides you get on copper, but it can still work, if you're willing to give it more time to work. Citric acid is generally considered to be pretty harmless in the dilute form you'll use it (just as it is in food). Either citric acid or sodium bisulphate pickels can normally, when diluted, go directly into a municipal waste water system. But you should check to see what their effect would be on a septic system. Septic systems are, as i said, a very different problem, since they are a living biological system, and more is involved than simply the toxicity of the chemical. Again, key to the answers are the quantities involved. Most of the chemicals you're using are not frequently disposed of, for example, and most of the issue is simple rinse water from pulling things out of the chemical and rinsing. You can deal with that with the rinse tanks I suggested. For the rest, you really need to check local regulations and requirements, as there are many variables beyond just the chemicals themselves. Peter |
#7
|
|||
|
|||
"Leo Lichtman" wrote in message
... Where I used to work we sold a system which could help you. It consisted of a metal 5-gal pail with a heater wrapped around the outside. It had a close-fitting plastic cover with a small fan, blowing air across the contents into a duct to the outside. ILLEGAL! :^) EPA calls this waste processing and you need all sorts of licensing and crap... 'course, it's probably only so for commercial enterprises. Tim -- "I've got more trophies than Wayne Gretsky and the Pope combined!" - Homer Simpson Website @ http://webpages.charter.net/dawill/tmoranwms |
#8
|
|||
|
|||
|
#9
|
|||
|
|||
Peter gave you good advise.
Do not dispose of pickle liquor or lubricants into your septic system or greywater system. By any state's laws (dictated by EPA) these are considered a hazardous waste and you can get in trouble that way. You could also ruin your septic system and contaminate your soil. Rinse water does not have the same concentrations and should not cause as much of a problem if you were attached to a municipal system, but since you have a septic system I would follow the advise and evaporate it. Most communities have household hazardous waste disposal and recycling events (also dictated by the EPA's new stormwater regulations) these would be ideal for any hobbyist to use (as I do). The following link should help you find a nearby site: http://www.earth911.org/ . Liz "lisau" wrote in message ... Hi. I just bought a house in the woods. The garage is a separate building, and I intend to set up a small metalworking shop to augment my woodworking -- I just graduated from school where I fell in love with metalsmithing while being a furniture major ... I especially love making small vessels & objects. The main problem is that there's no running water in the space, and no drainage pipes leading to my septic tank. The chemicals I use are silver, copper & nickel pickles, acid etching chems, patinas, and sometimes photography chemicals. Without spending a lot of $$, I figure I can set up a sink and feed it with a gardening hose -- I can do this easily right outside the garage's back door. But then I need to catch the runoff and dispose of it somehow. I don't really want to introduce this stuff into my septic tank, and feel uncomfortable with dumping it onto my hillside, even if I were to build a greywater system. I suppose I can dispose of it at the dump, but I'm lazy and would like to avoid that!!! Of course the long term solution would be to get a separate septic tank installed, or get a greywater sink that has a built-in filter, but that's going to take me a while to afford. Meanwhile, does anyone out there have similar circumstances? How do you deal with it? Does anyone know for sure the relative toxicity of the chems, and if neutralizing them with baking soda is enough to make it safe for a greywater system? I read on a previous thread about a woman who uses Spa Up (spa/pool chemical) instead of pickle -- is it really safer? Does it work for all metals? As with my woodworking, I want my metalworking to be as "green" as possible. Any comments on this issue would be appreciated! Thanks! lisau |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Smoky but safe | Christina Peterson | Beads | 15 | August 24th 04 04:51 AM |
Not sure if this is an ad, but just to be on the safe side... | starlia | Beads | 8 | July 6th 04 05:40 PM |
Food safe glass info ?? | WillMore | Glass | 2 | May 12th 04 01:23 AM |
How safe is lampworking in the house? | J's Girl | Beads | 40 | February 17th 04 07:56 PM |
Is crystal glass safe? | tsj | Glass | 14 | November 10th 03 09:16 PM |