If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Need advice troubleshooting machine
Either threaded wrong or gunked up tension disks most likely.
-- Ron Anderson A1 Sewing Machine PO Box 60 Sand Lake, NY 12153 518-674-8491 http://www.a1sewingmachine.com "AD" wrote in message m... My wife bought a sewing machine at an estate sale and now we both have hobbies. Hers is quilting (or attempting to quilt) on this machine and mine is repairing sewing machines! Background: The machine is a 1947 Kenmore. It was very complete including the original manual. I would describe it as in good but used condition. It required little to set up. We oiled all the points indicated in the manual. One thing it did not come with was a needle. We installed a generic Singer needle. The problem is the machine does not pull the stitches taunt. Last night was the worst I've seen--big loops on the bottom of the stitched piece. Adjusting both the bottom and top tensions had no noticable affect. Also when the machine is run at a decent speed it makes a knocking sound in the area where the needle goes down the little hole. The needle however seems sharp enough and had no visible damage such as dings or kinks. My wife in the past has also complained that she has to stop frequently to clear kinks of thread in or coming from the bobbin area. Can anyone clue me in as to what the problem might be? Should we chuck it in favor of something newer, say a 1972 model? In which case, anybody interested in a 1947 Kenmore? Muchas thanks |
Ads |
#2
|
|||
|
|||
You say quilting? An easy mistake to make with quilting is to forget to put
the presser foot down. That will also "royally" mess up your tension. "AD" wrote in message m... My wife bought a sewing machine at an estate sale and now we both have hobbies. Hers is quilting (or attempting to quilt) on this machine and mine is repairing sewing machines! Background: The machine is a 1947 Kenmore. It was very complete including the original manual. I would describe it as in good but used condition. It required little to set up. We oiled all the points indicated in the manual. One thing it did not come with was a needle. We installed a generic Singer needle. The problem is the machine does not pull the stitches taunt. Last night was the worst I've seen--big loops on the bottom of the stitched piece. Adjusting both the bottom and top tensions had no noticable affect. Also when the machine is run at a decent speed it makes a knocking sound in the area where the needle goes down the little hole. The needle however seems sharp enough and had no visible damage such as dings or kinks. My wife in the past has also complained that she has to stop frequently to clear kinks of thread in or coming from the bobbin area. Can anyone clue me in as to what the problem might be? Should we chuck it in favor of something newer, say a 1972 model? In which case, anybody interested in a 1947 Kenmore? Muchas thanks |
#3
|
|||
|
|||
if the needle is in backwards, it will royally screw up things. there is a
tension setting on most bobbin holders, too--could be either of these. good luck--happy untangling! admom Ron Anderson wrote in message ... Either threaded wrong or gunked up tension disks most likely. -- Ron Anderson A1 Sewing Machine PO Box 60 Sand Lake, NY 12153 518-674-8491 http://www.a1sewingmachine.com "AD" wrote in message m... My wife bought a sewing machine at an estate sale and now we both have hobbies. Hers is quilting (or attempting to quilt) on this machine and mine is repairing sewing machines! Background: The machine is a 1947 Kenmore. It was very complete including the original manual. I would describe it as in good but used condition. It required little to set up. We oiled all the points indicated in the manual. One thing it did not come with was a needle. We installed a generic Singer needle. The problem is the machine does not pull the stitches taunt. Last night was the worst I've seen--big loops on the bottom of the stitched piece. Adjusting both the bottom and top tensions had no noticable affect. Also when the machine is run at a decent speed it makes a knocking sound in the area where the needle goes down the little hole. The needle however seems sharp enough and had no visible damage such as dings or kinks. My wife in the past has also complained that she has to stop frequently to clear kinks of thread in or coming from the bobbin area. Can anyone clue me in as to what the problem might be? Should we chuck it in favor of something newer, say a 1972 model? In which case, anybody interested in a 1947 Kenmore? Muchas thanks |
#4
|
|||
|
|||
If you think that this machine will be one to keep, invest in a tune-up with
a Technician. It would be worth the $60 to have it running in top form. Maybe you can even get him to give you a quick once over to see if it is worth fixing. JMHO, Nana |
#5
|
|||
|
|||
AD wrote:
My wife bought a sewing machine at an estate sale [Snip] We oiled all the points indicated in the manual. One thing it did not come with was a needle. We installed a generic Singer needle. The problem is the machine does not pull the stitches taunt. 1. Use a different needle: Singer ones are not quite the same length as others. Schmetz is a good brand. 2. Check the thread path: big loops underneath the fabric mean not enough tension on the needle thread. Check that the thread is lying in the right place between the tension discs. If it is, try "flossing" between the tension discs using a piece of soft lint-free cloth. HTH -- Sally Holmes Wakefield, West Yorkshire, England |
#6
|
|||
|
|||
On 26 Aug 2003 12:39:21 -0700, AD wrote:
Background: The machine is a 1947 Kenmore. It was very complete including the original manual. I would describe it as in good but used condition. It required little to set up. We oiled all the points indicated in the manual. One thing it did not come with was a needle. We installed a generic Singer needle. Might do better with Schmetz on a Kenmore machine... depends on what it was timed for. piece. Adjusting both the bottom and top tensions had no noticable affect. Also when the machine is run at a decent speed it makes a knocking sound in the area where the needle goes down the little hole. Sounds like it needs a good cleaning (tensions and that lovely grey "felt pad" that builds up under the needleplate), and possibly some checking on threading... are you threading with presser foot up, then releasing the presser foot for sewing? That's something that's easy to forget to do when quilting. Check the needleplate and the bobbin case for dings... someone may have broken a needle and bent something just a smidge, too. Wind a new bobbin carefully... an] improperly wound bobbin can cause these sorts of snarls, too. Pretty good book, now out of print: Gale Grigg Hazen: Owner's guide to Sewing Machines, Sergers, and Knitting Machines. Kay Lancaster |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
RCTQ FAQs *where did the month go?* | Diana Curtis | Quilting | 20 | May 3rd 04 04:09 AM |
Slitting machine, Slitting, Rolling mill, Wire Flattening Mill, Sheet Leveler, Section Leveler, Scalping Machine, Brush Machine, coiler, decoiler, recoiler, 4 Hi, 6 Hi, 4 High, 6 High, Rolling mill, Wire Flattening Mill, Polishing Machine, Rewinding | korak | Marketplace | 0 | December 14th 03 05:52 PM |
Old Sewing Machine Advice | Diana Curtis | Beads | 9 | August 22nd 03 06:01 AM |
Machine Applique Advice | Monique Reed | Quilting | 7 | July 12th 03 09:58 PM |