A crafts forum. CraftBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » CraftBanter forum » Craft related newsgroups » Jewelry
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Sticky wax for buffing



 
 
Thread Tools Display Modes
  #11  
Old August 1st 08, 06:55 AM posted to rec.crafts.jewelry
Peter W.. Rowe,
external usenet poster
 
Posts: 355
Default Sticky wax for buffing

On Thu, 31 Jul 2008 09:40:21 -0700, in rec.crafts.jewelry eromlignod
wrote:

Thanks for all the replies. I ordered some dop wax from the link you
gave me.

Now...what is the best way to melt it?

What I'm using it for is to position some small mechanical parts onto
a flat surface. I need to be able to adjust their position and let
them harden in place. I would use glue, but I need to be able to re-
heat the wax and re-adjust the position in the future, if needed.

Will a hair dryer be hot enough to soften the wax for adjustment?
What other methods are there?

Don


Some sort of hot plate, or an electric griddle or electric fry pan, is another
method sometimes used to preheat stones and/or the wax for mounting on dop
sticks. Depending on your items, this might work for you too. Lapidary workers
often use a small wax heating pot to hold the melted wax in a soft plastic
state, not fully fluid, from which it's easily added to the end of a dop stick.
The wax blob of the stick is then easily adhered to the preheated stone, which
is often preheated on a small hot plate surface of the same appliance. But as I
said, people doing more of it used to use old electric fry pans to heat the
stones enough so the wax would stick. And the wax is often initially adhered to
the stick just by melting it onto the stick with an alcohol lamp if you don't
happen to have one of the little wax melting pots. The same lamp flame can also
be used to warm up the joined stick and stone a bit more to fully refine the
connection. Simple tech, but it works well enough. As Carl mentioned,
prepainting the surfaces with shellac (dilute it so it dries faster. You only
need a thin film) gives the wax something it will stick to even if the item is
only slightly warmed, since dop wax is usually based on a shellac formula...

And also as mentioned, chasers pitch is another good option to consider. That's
what is used to hold lens blanks for polishing in optics, I believe. Melts
somewhat hotter than typical dop waxes, but gives a stronger joint too.

Peter
Ads
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Help with Buffing. ABC[_2_] Jewelry 18 October 8th 07 05:44 PM
Question on Buffing Technique Curtis Gates Jewelry 4 January 8th 07 03:09 AM
Best fabric for (homemade) buffing wheels? [email protected] Polymer Clay 12 October 11th 05 03:51 PM
Buffing - finally! Carla Polymer Clay 10 January 6th 05 05:26 PM
Buffing Beads Juanita Floyd Polymer Clay 4 October 28th 03 07:03 PM


All times are GMT +1. The time now is 10:30 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 CraftBanter.
The comments are property of their posters.