If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
nylon fabric edge
Hi,
I came across an umbrella, the other day, with NO hem, on the outer edge. My wife told me that it's because they cut it so that the edge of the material is where the hem would be, had it been cut there. Can anyone tell me how the edge of the fabric is made so that no hem is visible? Thanks, John |
Ads |
#2
|
|||
|
|||
nylon fabric edge
"Shinnen" wrote:
Hi, I came across an umbrella, the other day, with NO hem, on the outer edge. My wife told me that it's because they cut it so that the edge of the material is where the hem would be, had it been cut there. Can anyone tell me how the edge of the fabric is made so that no hem is visible? Hot knife. Actually, I think they use a hot wire, but it's the same idea. If you melt/sear the edges of the nylon, it won't fray. It can be done with a candle, if you've practiced on scraps, although an easier way is to use a soldering iron or a woodbruning tool. -- Jenn Ridley : WIP: Oriental Butterfly, Floral Sampler, Rose Trio, Carousel (TW) Most recently Finished: Insect Sampler, TicTacToe Sampler, Snow Stitching log: http://jenn-stitch.livejournal.com/ |
#3
|
|||
|
|||
nylon fabric edge
Hi Mirjam,
I can see fibre, so I'm assuming it's not cast. Hi Jen, I use the soldering iron technique for "basting", when I'm sewing panels together. It works very well. I've even tried cutting the panels out with my soldering iron, but it make a very course line, and I think I'm missing something. I'd like to learn to do it, because it prevents further fraying. If you have any suggestions I'd appreciate it. Thanks, John |
#4
|
|||
|
|||
nylon fabric edge
"Shinnen" wrote:
Hi Mirjam, I can see fibre, so I'm assuming it's not cast. Hi Jen, I use the soldering iron technique for "basting", when I'm sewing panels together. It works very well. I've even tried cutting the panels out with my soldering iron, but it make a very course line, and I think I'm missing something. I'd like to learn to do it, because it prevents further fraying. If you have any suggestions I'd appreciate it. I was taught to cut the fabric to shape first and then sear the edges by running them along a soldering iron. I've also done it by passing the cut edge through a candle flame. (The candle flame takes more practice, but is doable.) -- Jenn Ridley : WIP: Oriental Butterfly, Floral Sampler, Rose Trio, Carousel (TW) Most recently Finished: Insect Sampler, TicTacToe Sampler, Snow Stitching log: http://jenn-stitch.livejournal.com/ |
#5
|
|||
|
|||
nylon fabric edge
Thanks Jenn ... John
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
5th Annual Boo-apalooza Halloween Swap | frood | Quilting | 20 | August 21st 05 01:28 PM |
My next project | Trish Brown | Sewing | 11 | April 27th 04 10:42 AM |
Not enough fabric! | Faren | Needlework | 7 | December 30th 03 05:50 AM |
Tapestry frame or embroidery hoop | Jill Spottiswoode | Needlework | 7 | September 22nd 03 10:27 AM |