A crafts forum. CraftBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » CraftBanter forum » Craft related newsgroups » Jewelry
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Traditional hand drill



 
 
Thread Tools Display Modes
  #1  
Old November 30th 09, 12:08 AM posted to rec.crafts.jewelry
Zoot
external usenet poster
 
Posts: 1
Default Traditional hand drill

I am interested in using traditional hand tools for jewelry
fabrication. I understand there are several types of hand drills;
spiral drill, hand crank drill, and the kind that uses a stick and
rope. I have a Dremel and don't want to spend on a flex shaft yet.
What is the best bet for a traditional hand drill to drill holes up
to, say 1 mm or so?
Ads
  #2  
Old November 30th 09, 12:18 AM posted to rec.crafts.jewelry
Peter W. Rowe[_2_]
external usenet poster
 
Posts: 115
Default Traditional hand drill

On Sun, 29 Nov 2009 15:08:03 -0800, in rec.crafts.jewelry Zoot
wrote:

I am interested in using traditional hand tools for jewelry
fabrication. I understand there are several types of hand drills;
spiral drill, hand crank drill, and the kind that uses a stick and
rope. I have a Dremel and don't want to spend on a flex shaft yet.
What is the best bet for a traditional hand drill to drill holes up
to, say 1 mm or so?


Since you already have a dremel tool, I'd say use it. You can get collets in
any size below the 1/8 inch maximum of most dremels, all the way down to a
collet that will hold a #80 drill bit, and the dremel's high speed is fine with
small drill bits. Use a suitable cutting lube and a light touch.

If you want a manual/traditional tool, the hand crank is the easiest for a
novice to use, but a bit clumsy to handle for tiny drill bits. The bow drill
(your stick and rope) is an old traditional tool that is very capable and
versatile in the hands of someone used to them, and still in use in parts of the
world lacking more modern (electric) tools for the job, but it takes
considerable practice to use well. For beginners with them, they're frustrating
as hell (but then, so is a hand crank drill if you're trying to drill really
tiny holes.) For one thing, bow drills are perhaps most effective when you make
your own drill bits as "spade" point bits that cut in both directions (clockwise
and counterclockwise, with one cutting edge active in each direction) Making
the appropriate bits is a whole additional skill in itself.

The litle spiral drills are a very slow and gentle tool. Mostly used by
watchmakers, more than jewelers. Accurate, but as I said, very slow to use.

So again, since you've already got a dremel, I'd suggest it as your best choice.
That's especially true if you've got one of the versions that has a speed
control on it, rather than just on/off.

Peter Rowe
  #3  
Old December 10th 09, 03:18 AM posted to rec.crafts.jewelry
Maren at google
external usenet poster
 
Posts: 311
Default Traditional hand drill

On Nov 29, 1:08 pm, Zoot wrote:
I am interested in using traditional hand tools for jewelry
fabrication. I understand there are several types of hand drills;
spiral drill, hand crank drill, and the kind that uses a stick and
rope. I have a Dremel and don't want to spend on a flex shaft yet.
What is the best bet for a traditional hand drill to drill holes up
to, say 1 mm or so?


Second what Peter says, if you already have a Dremel you might as well
use it. I got myself a drill press (they don't call it that but it is
one) to go
with ours, it works better for what I do than the flex shaft does (we
have
one, I tried both and for the time being the Dremel is almost
permanently
mounted in the drill press.

I drill hard wood seeds with 1/16" drill bits without problems. For
drilling
gemstones or the like, as Peter said, you'll need a lubricant/coolant.
Water may do fine.

Aloha,
Maren
HiloBeads: Beads - Beading Supplies - Hand-made Jewelry
Website: http://www.hilobeads.com/
Etsy: http://hilobeads.etsy.com/ -- Job's Tears for the AGLF
Blog: http://hilobeads.blogspot.com/
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
reamer and DTH hammer, drill tube, drill rod, drill bit, rock bit, Bin Glass 0 August 28th 06 04:36 AM
core bit, core barrel,drill bit, drill rod, shank adaptor, extension rod Bin Glass 0 August 28th 06 04:33 AM
6 Hand Carved Miniature Korean Figures Traditional Garb .. Doll Houses 1 May 10th 05 02:02 AM
Small drill TRCB General Crafting 5 May 1st 05 08:29 PM
Drill for rocks Mick Carving 6 October 8th 04 12:54 PM


All times are GMT +1. The time now is 09:19 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 CraftBanter.
The comments are property of their posters.