If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
cake stand
Hello Everyone,
I threw a tall pedestal all the way down to the bat and I threw a 12 inch plate form and they both turned out great but when I attatched the pedestal to the plate it looks like it bows up in the middle of the plate like if you put a marble in the exact middle of the plate it would roll to the edge of the plate. What did I do wrong? Thanks for any thoughts on this. Sandi |
Ads |
#2
|
|||
|
|||
Could you have attached the plate to the pedestal too soon and it sagged?
If that is not the case then when you were throwing, that is how you pulled out the floor which is actually really easy to do. Did you take a very wide rib and go over the floor once you pulled it out? "Red Deer" wrote in message oups.com... Hello Everyone, I threw a tall pedestal all the way down to the bat and I threw a 12 inch plate form and they both turned out great but when I attatched the pedestal to the plate it looks like it bows up in the middle of the plate like if you put a marble in the exact middle of the plate it would roll to the edge of the plate. What did I do wrong? Thanks for any thoughts on this. Sandi |
#3
|
|||
|
|||
I just now read on clayart how someone had a problem with a plate they threw
with a new clay which is just what you described. They swear that the plate was flat before drying but after was 1/8th of an inch higher in the center. They are trying to decide if it is an issue of it drying unevenly. It is nothing I have ever seen but one more piece of info to add to the mix. "dkat" wrote in message news Could you have attached the plate to the pedestal too soon and it sagged? If that is not the case then when you were throwing, that is how you pulled out the floor which is actually really easy to do. Did you take a very wide rib and go over the floor once you pulled it out? "Red Deer" wrote in message oups.com... Hello Everyone, I threw a tall pedestal all the way down to the bat and I threw a 12 inch plate form and they both turned out great but when I attatched the pedestal to the plate it looks like it bows up in the middle of the plate like if you put a marble in the exact middle of the plate it would roll to the edge of the plate. What did I do wrong? Thanks for any thoughts on this. Sandi |
#4
|
|||
|
|||
i expect flat-ish pieces to continue to sag even via the fire. it's a
little dicy, but i compensate (or swag) shapes with an expectation of this sag after firing. sometimes i nail it. sometimes i get bowlish pieces. sometimes i get DEAD flat pieces which are actually worthless to me. ones that go too far turn into something else... one way i was told to make goblet style pieces is to throw the stem attached to the leather hard bowl (or cup). for me it insures a straighter stem & an oportunity to refine the shape to suit that overall piece. see ya steve |
#5
|
|||
|
|||
Thanks to all who answered my querry. The plate was very flat when I
threw it and it dried very flat. Perhaps I did attatch the pedestal too soon. And no matter which way you set it to dry, the center of the plate has a weight stress on it, right side up or upside down. Sandi |
#6
|
|||
|
|||
If this was flat when it dried then I agree with Steve. Broad, flat things
sag in the firings. I have had large pieces that even come through the bisque the shape I want and then sag with the glaze. I know those who fire with supports under the piece even when it is the glaze firing when the piece is very wide. Good luck on getting what you want. Donna "Red Deer" wrote in message ups.com... Thanks to all who answered my querry. The plate was very flat when I threw it and it dried very flat. Perhaps I did attatch the pedestal too soon. And no matter which way you set it to dry, the center of the plate has a weight stress on it, right side up or upside down. Sandi |
#7
|
|||
|
|||
I have one just like what you described. I think that if I had thrown my
base wider at the top (where it sticks to the plate) it would have supported the plate better. You could try drying it with less stress if you dry it upside down but on top of something round so that the rim overhangs and is not touching anything. Good luck, Crystal "Red Deer" wrote in message oups.com... | Hello Everyone, | I threw a tall pedestal all the way down to the bat and I threw a 12 | inch plate form and they both turned out great but when I attatched the | pedestal to the plate it looks like it bows up in the middle of the | plate like if you put a marble in the exact middle of the plate it | would roll to the edge of the plate. What did I do wrong? | Thanks for any thoughts on this. | Sandi | |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
OT Chocolate Volcanos | NanaV | Quilting | 8 | October 29th 04 11:40 PM |
Lap stand for Q snaps or hoops? | Katherine Hutter | Needlework | 3 | October 7th 04 11:53 PM |
Easy cake recipe | SlinkyToy | Yarn | 1 | October 21st 03 06:56 PM |
The new stand - DH is wonderful | John Quinn | Needlework | 1 | September 12th 03 04:44 PM |
Rum Cake | Katherine Burgess | Yarn | 9 | August 14th 03 04:23 AM |