DIAMOND CORE BITS

Hi,

a while ago a guy was posting to this group advertising sets of diamond core
bits. 4 sizes thru 1/2"

anyone have his address. I am in need of 1/2 OD bits.

any advise on good bits

thks
bg


--
"Poor people have access to the courts in the same sense that Christians had
access to the lions."

- Judge Earl Johnson Jr.

www.harborfreight.com may have what you are looking for


"Boner the Cat" wrote in message
. com...
Hi,

a while ago a guy was posting to this group advertising sets of diamond
core
bits. 4 sizes thru 1/2"

anyone have his address. I am in need of 1/2 OD bits.

any advise on good bits

thks
bg


--
"Poor people have access to the courts in the same sense that Christians
had
access to the lions."

- Judge Earl Johnson Jr.

Boner the Cat wrote:

Hi,

a while ago a guy was posting to this group advertising sets of diamond core
bits. 4 sizes thru 1/2"

anyone have his address. I am in need of 1/2 OD bits.

any advise on good bits

thks
bg

--
"Poor people have access to the courts in the same sense that Christians had
access to the lions."

- Judge Earl Johnson Jr.

http://www.waleapparatus.com/search_...N=&PRODUCT_ID=
--
Jack


http://photos.yahoo.com/bc/xmissionbobo/

this guys prices are just so over the top that it is a wonder he sells
anything.

the Chinese guy was selling 4 bits for 12.95 and they are good bits.


"nJb" wrote in message
...
Boner the Cat wrote:

Hi,

a while ago a guy was posting to this group advertising sets of diamond
core
bits. 4 sizes thru 1/2"

anyone have his address. I am in need of 1/2 OD bits.

any advise on good bits

thks
bg

--
"Poor people have access to the courts in the same sense that Christians
had
access to the lions."

- Judge Earl Johnson Jr.


http://www.waleapparatus.com/search_...N=&PRODUCT_ID=
--
Jack


http://photos.yahoo.com/bc/xmissionbobo/

hey they have the 1/2 " I require..many thks

bg

"Moonraker" wrote in message
news
www.harborfreight.com may have what you are looking for


"Boner the Cat" wrote in message
. com...
Hi,

a while ago a guy was posting to this group advertising sets of diamond
core
bits. 4 sizes thru 1/2"

anyone have his address. I am in need of 1/2 OD bits.

any advise on good bits

thks
bg


--
"Poor people have access to the courts in the same sense that Christians
had
access to the lions."

- Judge Earl Johnson Jr.

They also have some small, thin diamond cut-off wheels that I use for
cutting brass and zinc. There are 5 of them and an arbor for your Dremel on
a blister pack. Reg price is $10., on sale this next week or so for $2.95.
I'm stocking up!!!

"Boner the Cat" wrote in message
om...
hey they have the 1/2 " I require..many thks

bg

"Moonraker" wrote in message
news
www.harborfreight.com may have what you are looking for

Boner the Cat wrote:

this guys prices are just so over the top that it is a wonder he sells
anything.

the Chinese guy was selling 4 bits for 12.95 and they are good bits.


I buy a lot of things from the Chinese guy and most of it is fine. Some
if it is junk. For example, a heavy duty wire wheel for my angle
grinder. The price is great at $4.99. But it is so out of balance that
you can't use it for very long without destroying your hands.

I offered you an alternative source from a quality company. If the
Chinese core drills do the job, by all means buy them. Report back with
your results.

--
Jack


http://photos.yahoo.com/bc/xmissionbobo/

I use those thin cut-off wheels for zinc and brass
They work great! But when it comes to lead----
I'm still deforming the lead no matter what I use,
including the lead knife. Especially when cutting
an angle greater than 45 degrees. Suggestions?
Hal

"Moonraker" wrote in message
...
They also have some small, thin diamond cut-off wheels that I use for
cutting brass and zinc. There are 5 of them and an arbor for your Dremel
on
a blister pack. Reg price is $10., on sale this next week or so for
$2.95.
I'm stocking up!!!

"Boner the Cat" wrote in message
om...
hey they have the 1/2 " I require..many thks

bg

"Moonraker" wrote in message
news
www.harborfreight.com may have what you are looking for

http://cgi.ebay.com/ws/eBayISAPI.dll...tem=3714282152

I'll let you know how it works as soon as it gets here. It uses a single
edge razorblade in a guillotine fashion.



"Harold E. Keeney (Hal)" wrote in message
...
I use those thin cut-off wheels for zinc and brass
They work great! But when it comes to lead----
I'm still deforming the lead no matter what I use,
including the lead knife. Especially when cutting
an angle greater than 45 degrees. Suggestions?
Hal

"Moonraker" wrote in message
...
They also have some small, thin diamond cut-off wheels that I use for
cutting brass and zinc. There are 5 of them and an arbor for your
Dremel
on
a blister pack. Reg price is $10., on sale this next week or so for
$2.95.
I'm stocking up!!!

"Boner the Cat" wrote in message
om...
hey they have the 1/2 " I require..many thks

bg

"Moonraker" wrote in message
news www.harborfreight.com may have what you are looking for

At least for larger cuts, I use an ordinary bandsaw for cutting lead and
aluminum....
But then, they aren't exactly precision cuts!

:-)

--Rick

"Harold E. Keeney (Hal)" wrote:

I use those thin cut-off wheels for zinc and brass
They work great! But when it comes to lead----
I'm still deforming the lead no matter what I use,
including the lead knife. Especially when cutting
an angle greater than 45 degrees. Suggestions?
Hal

"Moonraker" wrote in message
...
They also have some small, thin diamond cut-off wheels that I use for
cutting brass and zinc. There are 5 of them and an arbor for your Dremel
on
a blister pack. Reg price is $10., on sale this next week or so for
$2.95.
I'm stocking up!!!

"Boner the Cat" wrote in message
om...
hey they have the 1/2 " I require..many thks

bg

"Moonraker" wrote in message
news www.harborfreight.com may have what you are looking for