A crafts forum. CraftBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » CraftBanter forum » Craft related newsgroups » Pottery
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

New Kiln



 
 
Thread Tools Display Modes
  #1  
Old July 1st 03, 05:37 PM
Bri
external usenet poster
 
Posts: n/a
Default New Kiln

Hello All:

I am very new to this stuff and could use some pointers, but last week I
came across a great deal on a kiln and wheel. The kiln has never been
assembled, it is about 30 years old, it was sold by Westby Ceramic
supply and is 4 rows of 8 bricks each, 3 rows have heating elements and
one row is a spacer row. I don't know where the spacer row is supposed
to be located in the stack, or if it even maters where it is placed. I
had to lay out bricks and trace the ring on them and cut the bricks to
shape for the lid and base of the thing. It's all held together with
bands, 2 for each ring and one for the lid and one for the base. Now I
need to coat the lid and base with this mortar stuff that is in the kit
and install the coils and wiring. The wiring is asbestos covered so I
don't want to mess with it. What do kilns use now a days for wire that
will hold up to the heat? Does anyone have info or experience with one
of these kilns?
Also the wheel that I got is called a spinning tiger. It is missing the
rubber drive thing on the motor shaft so I ordered one from Creative
supply, it seemed awfully expensive for a piece of rubber, It doubled my
cost for the whole outfit!, I got the kiln, Wheel and a box of clay for
$25.
Anyhow, please post any helpful comments that you may have, Thanks,
Brian
  #2  
Old July 2nd 03, 03:28 AM
MKent41616
external usenet poster
 
Posts: n/a
Default

i hav eno clue as to how to assempble it but my 1st question is are you
complainging about the price or bragging ) as for the asbestos wireing it
will need to be takes and disposed of at a hazardous materials site. check with
a local suppy hous eon wireing and information. I would recomend
www.kickwheel.com in atlanta or davens i forget their email address. the
heating elements i woudl imagine are probably ok but if not i think they could
recomend some replacements for you also.


"Democracy is two wolves and a lamb voting on what to have for
lunch. Liberty is a well-armed lamb contesting the vote."

-- Benjamin Franklin, 1759
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Important - Please beware of a company called Bohle Eric Russell Glass 2 August 23rd 04 07:46 PM
Fusing/slumping/casting with kiln sitter Gordon Watt Glass 13 December 11th 03 04:46 PM
Good news, and agonizing over kiln purchase Kalera Stratton Beads 0 October 14th 03 06:11 PM
F/A @ EBAY Electric Kiln BATMAN.ROBIN Marketplace 0 September 17th 03 10:51 PM
Kiln question Kalera Stratton Beads 13 July 11th 03 06:35 AM


All times are GMT +1. The time now is 03:59 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 CraftBanter.
The comments are property of their posters.