Send him he

http://www.ganoksin.com/server-cgi-bin/iglimpse

--

Don Thompson

~~~~~~~~

"Peter W. Rowe" wrote in message
...
On Sun, 04 Jul 2004 07:31:59 -0700, in hô Jack Schmidling
wrote:

"ted.ffrater"

Not again....
Hi Jack.

good that you took the time to put him down a bit, and did it politely
too. I
was tempted myself. But moderators need to stay impartial, after all...

Ted's not a bad sort, just a rather old school european smith with
typically
european attitudes about how quickly one can learn this craft. Your post
apparently gave him an overblown impression of how much of a beginner you
might
be. Somehow, after looking at your web site, i don't doubt you know more
than
you realize, just maybe haven't done it yet... (grin)

Ted's post does have some good starting points, he's just coming at it
from a
typically european persepctive on silversmithing, which sometimes tends to
make
a deep arcane art which takes years to learn, out of something we here in
the
states have sophomore jewelry students doing happily by the end of the
second
month of the fall semester... He's right in that real mastery of the
craft of
silver smithing on the holloware level takes significant time and energy
to
learn well, but I think he forgets just how much even a beginner can learn
and
achieve on even the first piece.

In european training, actual holloware, like raising the goblet in the
first
place, is considered advanced work, and i think he never quite got past
that
point to your real questions about soldering. Plus, he's right about your
initial post suggesting, possibly correctly, that you're a bit of a
beginner,
given your reticence to work with a torch (which in the end is easier than
an
iron). But I'll disagree with him that it's so hard to learn.

A couple thoughts.

First, while I don't know a good web site that just directly shows you to
solder
with a torch, most good jewelry making books will cover it, and jewelry
scale
soldering is the same as what you're doing, except you might benefit from
a
larger torch, such as the air/acetyelene smith or prestolite torches.
Very nice
for silversmithing work with the larger tips, and just what you need for
such
things.

Please don't consider using any solder that melts low enough for an iron.
Even
the silver bearing ones are just not good strong joints. They DO offer
the
advantage of no fire scale or annealing, but thier color match is poor,
and once
used, you then cannot use proper silver soldering temps, or many
techniques, on
the piece again, as the low melting solders then cause trouble. If you
must use
such, consider instead the slightly pricier "TIX" brand. Not sure if it
contains silver, but it's intended for jewelry use, and stays a bit
brighter
looking, plus it melts even lower than what you've probably got now. Even
with
these solders, you'll have the best luch using a small torch to put the
pieces
on.to the goblet. You'll need to be using something like closed back
bezels, or
other solid back findings, rather than typical open backed heads, which
simply
don't offer enough surface area for the low melting solders to give a
useable
joint.

One web site you can go to for some reasearch is the Ganoksin.com site.
it's
the home of the Orchid mail list, a far busier discussion site for jewelry
makers and hobbyists, and searching the archives of that site will no
doubt find
you some instructional posts on soldering. Look up also, my own
discussions on
that site for the use of Prips flux (or misspelled Pripps flux) for how to
avoid
the problems with fire scale on silver when hard soldering. There are
also many
discussions on best choices of torches, etc.

And if you like feel free to contact me via private email for any
additional
pointers or questions you might run into. I'll be happy to help you
figure this
out. Sounds like a fun project.

By the way, your web site is inspiring indeed. How do you find the time
for
quite so many projects and interests?

Cheers

Peter